2006-2011 Camry Aurion · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY

  1. B146666E01
    Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.


2. INSTALL FRONT SEATBACK ASSEMBLY (for Manual Seat)
w/o airbag system (Click here).
w/ airbag system (Click here).

3. INSTALL FRONT SEATBACK ASSEMBLY (for Power Seat)
w/o airbag system (Click here).
w/ airbag system (Click here).

4. INSTALL FRONT SEAT HEADREST SUPPORT (for Manual Seat)

  1. B134683
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


5. INSTALL FRONT SEAT HEADREST SUPPORT (for Power Seat)

  1. B134683
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


6. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Manual Seat)

  1. B134682E02
    Engage the 14 clamps.

  1. Install the front seatback board sub-assembly with the 2 screws.


7. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Power Seat)

  1. B134682E02
    Engage the 2 claws.

  1. Engage the 14 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


8. INSTALL FRONT INNER SEAT CUSHION SHIELD (for Manual Seat)

  1. B148648
    Engage the 2 claws.

  1. Install the front inner seat cushion shield with the screw.


9. INSTALL FRONT INNER SEAT CUSHION SHIELD (for Power Seat)

  1. B146655
    Install the front inner seat cushion shield with the screw.

  1. Engage the 3 claws.


10. INSTALL FRONT SEAT CUSHION SHIELD (for Manual Seat)
  1. Connect the connector. (w/ lumber support)

  1. B149580
    Engage the 2 claws.

  1. Install the front seat cushion shield with the 2 screws.

  1. B153813
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


11. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY (for Power Seat)

  1. B134673
    Connect the connector.

  1. Engage the 2 claws.

  1. Install the front seat cushion shield assembly with the 5 screws.

  1. B146651
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


12. INSTALL RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

  1. B148952
    Engage the claw to install the reclining adjuster release handle.


13. INSTALL VERTICAL ADJUSTING HANDLE (for Manual Seat)

  1. B139104
    Install the No. 2 vertical adjusting handle with the 2 screws.


14. INSTALL VERTICAL ADJUSTER COVER LH (for Manual Seat)

  1. B148953
    Engage the 2 claws to install the vertical adjuster cover.


15. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for Power Seat)

  1. B149597
    Install the slide and vertical power seat switch knob.


16. INSTALL RECLINING POWER SEAT SWITCH KNOB (for Power Seat)

  1. B149596
    Install the reclining power seat switch knob.


17. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Connect the connector and clamp.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B139101
    Temporarily install the front seat track bracket with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B139102
    Temporarily install the rear seat track bracket with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


18. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
  1. Place the seat in the cabin.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. B149590
    Temporarily install the front side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. B139102
    Temporarily install the rear side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


19. INSTALL INNER SEAT TRACK BRACKET COVER (for Manual Seat)

  1. B149588E01
    Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover inner to engage claw B.


20. INSTALL INNER SEAT TRACK BRACKET COVER (for Power Seat)

  1. B149588E01
    Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover to engage claw B.


21. INSTALL OUTER SEAT TRACK BRACKET COVER (for Manual Seat)

  1. B149587E01
    Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the outer seat track bracket cover to engage claw B.


22. INSTALL OUTER SEAT TRACK BRACKET COVER (for Power Seat)

  1. B149587E01
    Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track cover to engage claw B.


23. INSTALL FRONT SEAT HEADREST ASSEMBLY

24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat)

25. INSPECT SLIDE ADJUSTER LOCK (for Manual Seat)

26. INSPECT SRS WARNING LIGHT (w/ Airbag System)
Inspect the SRS warning light. (Click here)

27. INSPECT FRONT SEAT ASSEMBLY (for Power Seat)
  1. Inspect the power seat operation.

← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (from Oct 2006) →