2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Front Clearance Sonar Sensor Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

There is an open or short circuit in the communication line between the front sensors and the clearance warning ECU, or there is a malfunction in a front sensor.
B157386E01

WIRING DIAGRAM

B139283E05

INSPECTION PROCEDURE


1. CHECK CLEARANCE SONAR SYSTEM
  1. Check the operation of the clearance sonar system (Click here).

    Result:
    Result
    Proceed to
    Warning message is displayed on multi-information display and all front clearance sensor indicators are blinking
    A
    Warning message is displayed on multi-information display and front left clearance sensor or front right clearance sensor indicator is blinking
    B



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - FRONT LEFT SENSOR)

  1. B139274E06
    Disconnect the O30 ECU connector.

  1. Disconnect the A69 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O30-21 (BOF) - A69-1 (BI)
    Always
    Below 1 Ω
    O30-9 (SOF) - A69-3 (SI)
    O30-19 (E1) - A69-5 (EI)
    O30-21 (BOF) - Body ground
    10 kΩ or higher
    O30-9 (SOF) - Body ground
    O30-19 (E1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT CLEARANCE WARNING ECU ASSEMBLY

  1. B139288E05
    Reconnect the O30 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O30-19 (E1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O30-21 (BOF) - Body ground
    Engine switch on (IG)
    7 to 9 V



NG
REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)
OK


4. REPLACE NO. 1 ULTRASONIC SENSOR (FRONT LEFT SENSOR)

  1. B139335E01
    Replace the ultrasonic sensor (Click here) with a normally functioning sensor.

    HINT:
    All the corner sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


5. CHECK CLEARANCE SONAR SYSTEM
  1. Check the operation of the clearance sonar system (Click here).

    Result:
    Result
    Proceed to
    Clearance sonar system malfunction
    A
    Clearance sonar system normal operation
    B



B
END
A


6. CHECK HARNESS AND CONNECTOR (FRONT LEFT SENSOR - FRONT RIGHT SENSOR)

  1. B139278E22
    Disconnect the A69 and A62 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A69-2 (BO) - A62-1 (BI)
    Always
    Below 1 Ω
    A69-4 (SO) - A62-3 (SI)
    A69-6 (EO) - A62-5 (EI)
    A69-2 (BO) - Body ground
    10 kΩ or higher
    A69-4 (SO) - Body ground
    A69-6 (EO) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. REPLACE NO. 1 ULTRASONIC SENSOR (FRONT RIGHT SENSOR)

  1. B139335E01
    Replace the ultrasonic sensor (Click here) with a normally functioning sensor.

    HINT:
    All the corner sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


8. CHECK CLEARANCE SONAR SYSTEM
  1. Check the operation of the clearance sonar system (Click here).

    Result:
    Result
    Proceed to
    Clearance sonar system malfunction
    A
    Clearance sonar system normal operation
    B



B
END
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← TERMINALS OF ECU (from Jun 2009)Front Clearance Sonar Sensor Circuit (from Jun 2009) →