2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

TL29 Key pad Circuit Power Short To Battery

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

When the emergency button is pressed, the voltage on the mayday ECU unit connector N46 terminal 13 will be approximately 3.8 V. The mayday ECU determines this voltage as an emergency button press.
The mayday ECU will initiate a voice call to an operator at the Toyota Link Call Centre and then send an SMS message containing status and location data. If the call cannot be connected, the mayday ECU will immediately re-attempt to connect the call a second time. If the second attempt also fails, the unit will wait for 60 seconds and make a third and final attempt.
If the emergency button is pressed while a Toyota Link call is in progress, the status of the call will be upgraded to an emergency call, and the mayday ECU will not be permitted to terminate the call by pressing the End Call button.
If the emergency button is pressed while the vehicle is outside GSM network range, the mayday ECU will enter Emergency Call mode, where by the emergency call request will be retained. When contact is re-established with the GSM network, the emergency call will be placed immediately.
During the mayday ECU self test, the key pad circuit is measured to detect if the voltage is too high. This self test is only performed once whenever the mayday ECU is powered up, at this time the power to the key pad is OFF.
DTC TL29 is set if the key pad circuit voltage is above 1.6 V when the supply is disabled.

INSPECTION PROCEDURE


1. CHECK MAYDAY ECU VOLTAGE

  1. B169483E01
    Turn the engine switch off.

  1. Disconnect the mayday ECU unit connector N46.

  1. Connect a digital multimeter between terminal 20 and ground.

  1. Turn the engine switch on (IG) and check for voltage.

    OK:
    Less than 12 - 14 V



OK
Go to step 3
NG


2. CHECK MAYDAY ECU

  1. B169476E01
    Reconnect the mayday ECU unit connector N46.

  1. Using the TDT, navigate to the Systems Menu.

  1. Select: Diagnosis / Data List, then scroll to Key pad voltage.

  1. Connect a digital multimeter between mayday ECU unit connector N46 terminal 13 and ground.

  1. Monitor the key pad voltage whilst operating the key pad.

    Standard:
    1.6 V

  1. In the Data List, is the key pad voltage greater than the specified value?



YES
Go to step 5
NO

INTERMITTENT FAULT, CHECK WIRE HARNESS AND CONNECTORS

3. CHECK ROOF CONSOLE BOX VOLTAGE

  1. B169476E01
    Disconnect the roof console box connector Q16.

  1. Turn the engine switch on (IG).

  1. Connect a digital multimeter between mayday ECU unit connector N46 terminal 13 and ground and check for voltage.

    OK:
    Greater than 1.6 V



NG
REPLACE THE ROOF CONSOLE BOX ASSEMBLY
OK


4. REPAIR SHORT CIRCUIT TO BATTERY
  1. Clear all DTCs (Click here) and then verify operation.


NEXT

END

5. CHECK MAYDAY ECU WIRE HARNESS

  1. B169478E01
    Disconnect the mayday ECU connectors A and B.

  1. Check for continuity between the mayday ECU unit connector N46 and connectors A and B.

    OK:
    Less than 1 Ω



NG
REPAIR OR REPLACE MAYDAY ECU WIRE HARNESS
OK


6. CHECK MAYDAY ECU CONNECTORS
  1. Are the mayday ECU connectors tight?



NO
REPAIR OR REPLACE THE CONNECTORS
YES

REPLACE MAYDAY ECU


← TL28 Key pad Circuit Power Short To Ground (from Oct 2006)TL29 Key pad Circuit Power Short To Battery (from Jun 2009) →