P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
While the engine is being cranked, the positive battery voltage is applied to terminal STA of the TCM.If the TCM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0617 |
When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to the TCM for 20 seconds. (1-trip detection logic): (a) Vehicle speed more than 20 km/h (12.4 mph) (b) Engine speed more than 1,000 rpm (c) STA signal ON |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click here).
- Read freeze frame data using the intelligent tester. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction (Click here).
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / ECT / Data List.
Check the value displayed on the tester when the ignition switch is turned on (IG) and the engine is started.
- OK:
Tester Display
Measurement Item/Range
Normal Condition
Starter Signal
Starter signal/ ON or OFF
ON: Cranking
|
|
||||
| NG | |
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch.

Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Gear Selector Lever Position
Tester Connection
Specified Condition
P
B(C1-4) - L(C1- 9)
Below 1 Ω
N
B(C1-4) - L(C1- 9)
Below 1 Ω
Reconnect the park/neutral position switch connector.
- Result:
Result
Proceed to
OK (without smart entry and start system)
A
OK (with smart entry and start system)
B
NG
C
|
|
||||
|
|
||||
| A | |
| 3. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY |
Disconnect the E23 ignition switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Switch Condition
Tester Connection
Specified Condition
LOCK
ST1 (E23-3) - AM1 (E23-4)
ST2 (E23-7) - AM2 (E23-5)
10 kΩ or higher
START
ST1 (E23-3) - AM1 (E23-4)
ST2 (E23-7) - AM2 (E23-5)
Below 1 Ω
Reconnect the ignition switch connector.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / ECT / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned on (IG) and the engine is started.
- OK:
Ignition Switch Condition
ON (IG)
ENGINE START
Starter Signal
OFF
ON
|
|
||||
| OK | ||
| ||
