Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › CURTAIN SHIELD AIRBAG ASSEMBLY
INSTALLATION
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
1.
INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Install 4 new clips and 4 new spacers to the curtain shield airbag assembly as shown in the illustration.
NOTICE:
Do not push in the pin.
Make sure that the clips are installed in the correct direction.
Make sure that the spacers are installed properly, in the correct direction, and that they are not damaged.
Install the curtain shield airbag assembly with 5 new bolts.
Torque:
11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
NOTICE:
Do not twist the curtain shield airbag assembly when installing it.
Install the 4 clips with the curtain shield airbag assembly to the body panel as shown in the illustration.
NOTICE:
Make sure that the pins of the clips are pushed in firmly.
Mark the clips.
HINT:
Mark the clips to make sure that they are not reused.
Connect the connector.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
2.
INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
Pull the roof headlining assembly into the vehicle through the rear left door.
Engage the 4 clips.
Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.
Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.
Install the radio setting condenser to the front pillar RH with the bolt.
Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.
3.
INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
Pull the roof headlining assembly into the vehicle through the rear left door.
Engage the hook, 4 clips, and 2 fasteners.
Connect the sliding roof drive gear connector.
Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.
Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.
Install the radio setting condenser to the front pillar RH with the bolt.
Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.
4.
INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that the joining point of the opening trim is on the left side of the vehicle as shown in the illustration.
NOTICE:
After installation, check that the corners fit correctly.
5.
INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)
Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.
Engage the 4 claws.
Engage the 6 claws and install the spot light assembly.
6.
INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)
Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.
Engage the 4 claws.
Engage the 4 claws and install the lens cover.
7.
INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Driver Side)
with Assist Grip:
Assemble the front assist grip sub-assembly as shown in the illustration.
Install the front assist grip sub-assembly.
8.
INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Front Passenger Side)
Assemble the front assist grip sub-assembly as shown in the illustration.
Install the front assist grip sub-assembly.
9.
INSTALL REAR ASSIST GRIP SUB-ASSEMBLY
HINT:
Use the same procedure for the rear side and the front side (Click here ).
10.
INSTALL VISOR HOLDER
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
HINT:
Use the same procedure for the RH side and the LH side.
11.
INSTALL VISOR ASSEMBLY LH
Engage the 2 clips and install the visor assembly LH.
Engage the 4 claws and install the visor bracket cover.
12.
INSTALL VISOR ASSEMBLY RH
Engage the 2 clips and install the visor assembly LH.
Engage the 4 claws and install the visor bracket cover.
13.
INSTALL ROOF CONSOLE BOX ASSEMBLY
Connect the connectors.
Engage the 2 claws and 2 clips, and then install the roof console box assembly.
14.
INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
Install the rain sensor cover.
15.
INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Install a new clip <A> on the front pillar garnish LH.
Engage the 2 claws and 2 clips, then install the front pillar garnish LH.
16.
INSTALL FRONT PILLAR GARNISH RH
Remove the protective cover.
Install a new clip <A> on the front pillar garnish RH.
Engage the 2 claws and 2 clips, then install the front pillar garnish RH.
17.
INSTALL ROOF SIDE INNER GARNISH LH
Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.
18.
INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure for the RH and LH side (Click here ).
19.
INSTALL UPPER CENTER PILLAR GARNISH LH
Engage the clip.
Install the upper center pillar garnish LH with the bolt.
20.
INSTALL LOWER CENTER PILLAR GARNISH LH
Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.
21.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Install the floor end of the front seat outer belt assembly LH with the bolt.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
22.
INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
Engage the 3 claws and install the lap belt outer anchor cover.
23.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Install the front door opening trim weatherstrip LH as shown in the illustration.
NOTICE:
After installation, check that the corners fit correctly.
24.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
25.
INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
26.
INSTALL UPPER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure for the RH and LH side (Click here ).
27.
INSTALL LOWER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure for the RH and LH side (Click here ).
28.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure for the RH side and the LH side.
29.
INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT:
Use the same procedure for the RH and LH side (Click here ).
30.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Install the front door opening trim weatherstrip RH as shown in the illustration.
NOTICE:
After installation, check that the corners fit correctly.
31.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure for the RH and LH side (Click here ).
32.
INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure for the RH and LH side (Click here ).
33.
INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH
Engage the 3 claws to install the rear door inner glass weatherstrip.
34.
INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Engage the claw to install the No. 1 door scuff plate clamp.
Connect each connector.
Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.
Engage the 7 clips to install the rear door trim board to the rear door panel.
Install the 3 screws.
35.
INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
Connect the connector.
Engage the claw and install the courtesy light assembly.
36.
INSTALL REAR ASH RECEPTACLE ASSEMBLY LH (w/ Ashtray)
Install the rear ash receptacle assembly.
37.
INSTALL DOOR ASSIST GRIP COVER LH
Engage the 6 claws and install the door assist grip cover.
38.
INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH
Engage the 3 claws to install the rear door inside handle bezel plug.
39.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Install the rear door opening trim weatherstrip LH as shown in the illustration.
NOTICE:
After installation, check that the corners fit correctly.
40.
INSTALL REAR DOOR SCUFF PLATE LH
Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.
41.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Install the rear door opening trim weatherstrip RH as shown in the illustration.
NOTICE:
After installation, check that the corners fit correctly.
42.
INSTALL REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure for the RH and LH side (Click here ).
43.
INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Install the rear side seatback assembly with the bolt.
Torque:
18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
44.
INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
Install the rear side seatback assembly with the bolt.
Torque:
18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
45.
INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Install the separate type rear seatback assembly with the 2 bolts.
Torque:
18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
46.
INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
Install the separate type rear seatback assembly with the 2 bolts.
Torque:
18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
47.
INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)
Place the seatback in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
Install the rear seatback assembly with the 4 bolts.
Torque:
18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.
Install the floor anchor part with the bolt.
48.
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)
49.
INSTALL REAR SEAT HEADREST ASSEMBLY
50.
INSTALL REAR SEAT CUSHION ASSEMBLY
for Fixed Seat Type: Click here
for Fold Down Seat Type: Click here
51.
INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
52.
INSTALL INNER SEAT TRACK BRACKET COVER LH (for Power Seat)
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
53.
INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Power Seat)
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
54.
INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)
55.
INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
56.
INSTALL INNER SEAT TRACK BRACKET COVER LH (for Manual Seat)
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
57.
INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Manual Seat)
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
58.
INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)
59.
INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)
HINT:
Use the same procedure for the RH and LH side.
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
60.
INSTALL INNER SEAT TRACK BRACKET COVER RH (for Power Seat)
HINT:
Use the same procedure for the RH and LH side.
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
61.
INSTALL OUTER SEAT TRACK BRACKET COVER RH (for Power Seat)
HINT:
Use the same procedure for the RH and LH side.
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
62.
INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)
63.
INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)
HINT:
Use the same procedure for the RH and LH side.
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
64.
INSTALL INNER SEAT TRACK BRACKET COVER RH (for Manual Seat)
HINT:
Use the same procedure for the RH and LH side.
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
65.
INSTALL OUTER SEAT TRACK BRACKET COVER RH (for Manual Seat)
HINT:
Use the same procedure for the RH and LH side.
for 2AZ-FE: Click here
for 2GR-FE LHD: Click here
for 2GR-FE RHD: Click here
66.
INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)
67.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat)
68.
INSPECT SRS WARNING LIGHT
Inspect SRS warning light (Click here ).
69.
INSPECT FRONT SEAT ASSEMBLY (for Power Seat)
Inspect the power seat operation.
70.
INSPECT SLIDE ADJUSTER LOCK (for Manual Seat)