2006-2011 Camry Aurion · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Also covers:

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using an intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch on (IG)
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM
P0724
The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3km/h (2mph)) and GO ( 30 km/h (19 mph) or more) fashion 5 times. (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM

A153048E01
A149030E03

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).


1. CHECK STOP LIGHT (OPERATION OF STOP LIGHT)
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK:
    Stop lights turn ON when brake pedal is depressed.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2. READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1 - VOLTAGE)

  1. FI07052E19
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.

  1. Check the STP signal when the brake pedal is depressed and released.

    OK:
    Brake Pedal Operation
    Specified Condition
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Enter the following menus: Powertrain / Engine / Data List / ST1.

  1. Check the ST1 signal when the brake pedal is depressed and released.

    OK:
    Brake Pedal Operation
    Specified Condition
    Depressed
    ST1 signal OFF
    Released
    ST1 signal ON



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. A072924E25
    Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    Switch pin free
    1 - 2
    Below 1 Ω
    Switch pin free
    3 - 4
    10 kΩ or higher
    Switch pin pushed in
    1 - 2
    10 kΩ or higher
    Switch pin pushed in
    3 - 4
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


4. CHECK ECM (STP, ST1 - VOLTAGE)

  1. A112585E11
    Disconnect the A24 (RHD) or A55 (LHD) ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    RHD:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    STP (A24-36) - Body ground
    Depressed
    9 to 14 V
    STP (A24-36) - Body ground
    Released
    0 to 3 V
    ST1- (A24-35) - Body ground
    Depressed
    0 to 3 V
    ST1- (A24-35) - Body ground
    Released
    9 to 14 V
    LHD:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    STP (A55-36) - Body ground
    Depressed
    9 to 14 V
    STP (A55-36) - Body ground
    Released
    0 to 3 V
    ST1- (A55-35) - Body ground
    Depressed
    0 to 3 V
    ST1- (A55-35) - Body ground
    Released
    9 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0500 Vehicle Speed Sensor "A" (from Jun 2009)P0504 Brake Switch "A" / "B" Correlation (+ P0724) (from Jun 2009) →