2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


BUS CHECK (COMMUNICATION MALFUNCTION DTC)

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.

  1. G029877E01
    Select "Bus Check" from the "System Select" screen on the intelligent tester.

  2. G029878
    Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

  3. G029879
    Select the system of the DTC to be checked and select "Details".

  4. G029880
    CAN communication system DTC(s) is/are displayed.


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
  1. Systems (ECUs, sensors) that use CAN communication vary depending on the vehicle's optional equipments. Check which systems (ECUs, sensors) are installed on the vehicle.

    ECU/Sensor name
    Check method
    ABS / VSC / TRC
    Installed on all vehicles
    Engine
    Installed on all vehicles
    ECT
    Installed on vehicles with automatic transaxle
    SRS Airbag
    Installed on all vehicles
    Air Conditioner
    Installed on all vehicles
    Combination Meter
    Installed on all vehicles
    Main Body
    Installed on all vehicles


DTC TABLE BY ECU

HINT:
  1. For the CAN communication system, CAN communication system DTCs stored in certain ECUs can be displayed using the intelligent tester.
  2. If CAN communication system DTCs are output, trouble cannot be determined only by the DTCs. Perform troubleshooting according to "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).

  1. ECM (2AZ-FE)

    DTC No.
    Detection Item
    U0101*
    High Speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *: The ECM is malfunctioning if only U0101 is output. Replace the ECM.

  2. ECM (2GR-FE)

    DTC No.
    Detection Item
    U0101*
    High speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *: The ECM is malfunctioning if only U0101 is output. Refer to SFI system (Click here).

  3. ECT (2AZ-FE)

    DTC No.
    Detection Item
    U0100*
    High Speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *: The ECM is malfunctioning if only U0100 is output. Replace the ECM.

  4. ECT (2GR-FE)

    DTC No.
    Detection Item
    U0100*
    High speed CAN Communication Bus

    HINT:
    1. DTC communication is via the CAN communication system.
    2. *: The ECM is malfunctioning if only U0100 is output. Refer to Automatic Transaxle system (Click here).

  5. SKID CONTROL ECU

    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus Off

    HINT:
    DTC communication is via the CAN communication system.

  6. COMBINATION METER ECU

    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129
    Lost Communication with Brake System Control Module

    HINT:
    DTC communication is via the CAN communication system.

  7. AIR CONDITIONER AMPLIFIER

    DTC No.
    Detection Item
    B1499
    Multiplex Communication Circuit

    HINT:
    DTC communication is via the CAN communication system.

  8. MAIN BODY ECU

    HINT:
    Although the main body ECU is connected to the CAN communication system, CAN communication DTCs are not output.

  9. CENTER AIRBAG SENSOR

    HINT:
    Although the center airbag sensor is connected to the CAN communication system, CAN communication DTCs are not output.


DTC COMBINATION TABLE
DTC
Trouble Mode
Output from
Output DTC
ECM Communication Stop Mode
Skid Control ECU Communication Stop Mode
Combination Meter ECU Communication Stop Mode
Air Conditioning Amplifier Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Main Body ECU Communication Stop Mode
Skid Control ECU
U0073
X
X
X
X
X
X
Combination Meter ECU
U0100
○
X
X
X
X
X
U0129
X
○
X
X
X
X
No DTC
X
X
○
○
○
○

HINT:
  1. ○: Set
  2. X: Not set or may be set depending on the malfunctioning part when one side of the CAN bus wire becomes open

  1. Perform troubleshooting according to the combination of DTCs output.

    HINT:
    1. ECM Communication Stop Mode (Click here)
    2. Skid Control ECU Communication Stop Mode (Click here)
    3. Combination Meter ECU Communication Stop Mode (Click here)
    4. Center Airbag Sensor Communication Stop Mode (Click here)
    5. Air Conditioning Amplifier Communication Stop Mode (Click here)
    6. Main Body ECU Communication Stop Mode (Click here)

← TERMINALS OF ECU (from Oct 2006)DIAGNOSIS SYSTEM (from Jun 2009) →