2006-2011 Camry Aurion · Service Manual TRANSMISSION

U0100 Lost Communication with ECM / PCM "A"

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The engine control unit intercommunicates with the TCM using the Controller Area Network (CAN).
If there is a problem in this intercommunication, the TCM sets a DTC.
DTC No.
DTC Detection Condition
Trouble Area
U0100
  1. Following conditions are met for 1.25 seconds (1-trip detection logic):
    1. Ignition switch on (IG)
    2. Battery voltage is 10.5 V or more
    3. No intercommunication between the ECM and TCM
TCM

WIRING DIAGRAM

C145250E03

INSPECTION PROCEDURE

HINT:
  1. If the CAN communication malfunctions, the TCM cannot receive the current data from the ECM. In this case, the freeze frame data output from the TCM have not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is effective to find malfunctions.


1. CHECK ECU TERMINAL VOLTAGE (+B AND E1 TERMINALS)

  1. C133210E26
    Disconnect the TCM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    C56-18 (+B) - Body ground
    9 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    C56-8 (E1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (TCM - ECM)

  1. C133242E07
    Disconnect the C56 TCM connector.

  1. Disconnect the C58*1 or C55*2 ECM connector.*1: for RHD*2: for LHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    C56-6 (CAN+) - C58-2*1 (CAN+)
    Below 1 Ω
    C56-6 (CAN+) - C55-2*2 (CAN+)
    Below 1 Ω
    C56-7 (CAN-) - C58-1*1 (CAN-)
    Below 1 Ω
    C56-7 (CAN-) - C55-1*2 (CAN-)
    Below 1 Ω
    C56-6 (CAN+) or C58-2*1 (CAN+) - Body ground
    1 MΩ or more
    C56-6 (CAN+) or C55-2*2 (CAN+) - Body ground
    1 MΩ or more
    C56-7 (CAN-) or C58-1*1 (CAN-) - Body ground
    1 MΩ or more
    C56-7 (CAN-) or C55-1*2 (CAN-) - Body ground
    1 MΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK IF DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC.

  1. Replace the TCM.

    HINT:
    Replace the TCM with the TCM of a normally functioning vehicle of the same model.

  1. Start the engine.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0100
    A
    No DTC
    B



B
REPLACE TCM
A

REPLACE ECM


← P2810 Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4) (from Oct 2006)U0100 Lost Communication with ECM / PCM "A" (from Jun 2009) →