2006-2011 Camry Aurion · Service Manual TRANSMISSION

Transmission Control Switch Circuit

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

When moving the shift lever into the S position using the transmission control switch, it is possible to switch the shift range position between "1" (first range) and "6" (sixth range).
Shifting up "+" once raises one shift range position, and shifting down "-" lowers one shift range position.

WIRING DIAGRAM

C122805E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

  1. C110345E23
    Disconnect the transmission control switch connector of the shift lock control unit assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Switch Condition
    Tester Connection
    Specified Condition
    Ignition switch on (IG)
    E31-3 - Body ground
    10 to 14 V
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

  1. C110345E23
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    E31-5 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT TRANSMISSION CONTROL SWITCH

  1. C110341E17
    Measure the resistance between each terminal of the shift lock control unit assembly when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    S, "+" and "-"
    E31-3 - E31-7
    Below 1 Ω
    Except S, "+" and "-"
    10 kΩ or higher
    Press continuously
    "+"
    (Up shift)
    E31-2 - E31-5
    Below 1 Ω
    S
    10 kΩ or higher
    Press continuously
    "-"
    (Down shift)
    E31-1 - E31-5
    Below 1 Ω
    S
    10 kΩ or higher



NG
REPLACE TRANSMISSION CONTROL SWITCH
OK


4. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

  1. G100098E12
    Connect the transmission control switch connector of the shift lock control unit assembly.

  1. Disconnect the A24*1 or A55*2 ECM connector.

  1. Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    S, "+" and "-"
    A24-25*1 (S) - Body ground
    A55-25*2 (S) - Body ground
    10 to 14 V
    Except S, "+" and "-"
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.*1: for RHD*2: for LHD

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    Press continuously
    "+"
    (Up shift)
    A24-16*1 (SFTU) - Body ground
    A55-16*2 (SFTU) - Body ground
    Below 1 Ω
    S
    10 kΩ or higher
    Press continuously
    "-"
    (Down shift)
    A24-51*1 (SFTD) - Body ground
    A55-51*2 (SFTD) - Body ground
    Below 1 Ω
    S
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← U0100 Lost Communication with ECM / PCM "A" (from Jun 2009)Park / Neutral Position Switch Circuit (from Oct 2006) →