2006-2011 Camry Aurion · Service Manual TRANSMISSION

Park / Neutral Position Switch Circuit

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.

WIRING DIAGRAM

C226005E01

INSPECTION PROCEDURE


DATA LIST

HINT:
According to the Data List displayed on the intelligent tester, you can read the value of switches, sensors, actuators and other items without removing any parts. Reading the Data List as the first step in troubleshooting is one method to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn on the tester.

  6. Enter the following items: "Powertrain / ECT / Data List".

  7. According to the display on the tester, read "Data List".

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    P and N: ON
    Except P and N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (D Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is;
    D and S: ON
    Except D and S: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.


1. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C110340E61
    Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    RB (C1-1) - PL (C1-3) and B (C1-4) - L (C1-9)
    Below 1 Ω
    Except P
    10 kΩ or higher
    R
    RB (C1-1) - RL (C1-2)
    Below 1 Ω
    Except R
    10 kΩ or higher
    N
    RB (C1-1) - NL (C1-8) and B (C1-4) - L (C1-9)
    Below 1 Ω
    Except N
    10 kΩ or higher
    D, S, "+" and "-"
    RB (C1-1) - DL (C1-7)
    Below 1 Ω
    Except D, S, "+" and "-"
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


2. INSPECT TRANSMISSION CONTROL SWITCH

  1. C110341E17
    Connect the park/neutral position switch connector.

  1. Disconnect the transmission control switch connector of the shift lock control unit assembly.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    S, "+" and "-"
    E31-3 - E31-7
    Below 1 Ω
    Except S, "+" and "-"
    10 kΩ or higher



NG
REPLACE TRANSMISSION CONTROL SWITCH
OK


3. CHECK ECU TERMINAL VOLTAGE (STA TERMINAL)

  1. C133210E04
    Connect the transmission control switch connector of the shift lock control unit assembly.

  1. Measure the voltage according to the value(s) in the table below while cranking the engine.

    Standard voltage:
    Tester Connection
    Specified Condition
    STA (C56-10) - Body ground
    9 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TCM - ECM)
OK


4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

  1. C133210E05
    Disconnect the TCM connector.

  1. Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    R
    R (C56-15) - Body ground
    10 to 14 V *
    Except R
    Below 1 V
    D
    D (C56-16) - Body ground
    10 to 14 V
    Except D
    Below 1 V

    HINT:
    *: The voltage will drop slightly because the back up light is turned on.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
OK

REPLACE TCM


← Transmission Control Switch Circuit (from Oct 2006)ECU Power Source Circuit (from Oct 2006) →