B2278 Engine Switch Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
This DTC is output when 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.- HINT:
- When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2278 |
Communication is abnormal between the main body ECU and engine switch or the engine switch is defective |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (START SWITCH) |
Connect the intelligent tester to the DLC3.
Check the DATA LIST for proper functioning of the start switch.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
St SW1
Start Switch 1 / ON or OFF
ON: Engine switch is pushed
OFF: Engine switch is not pushed
-
St SW2
Start Switch 2 / ON or OFF
ON: Engine switch is pushed
OFF: Engine switch is not pushed
-
- OK:
- ON (engine switch is pushed) and OFF (engine switch is not pushed) appear on the screen.
|
|
||||
| OK | |
| 2. CHECK ENGINE SWITCH CONDITION |
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:
- OK:
- off → on (ACC) → on (IG) → off
- HINT:
- If power mode does not change to ON (IG and ACC) (Click here).
- If power mode does not change to ON (IG) (Click here).
- If power mode does not change to ON (ACC) (Click here).
- If power mode does not change to ON (IG and ACC) (Click here).
|
|
||||
| OK | ||
| ||
| 3. INSPECT ENGINE SWITCH |
Remove the engine switch.


Disconnect the switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
7 (SS1) - 5 (GND)
Pushed
Below 1 Ω
2 (SS2) - 5 (GND)
Pushed
Below 1 Ω
7 (SS1) - 5 (GND)
Not pushed
10 kΩ or higher
2 (SS2) - 5 (GND)
Not pushed
10 kΩ or higher
- HINT:
- This switch is a momentary type switch.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND) |
Disconnect the E7 ECU connector.


Disconnect the E52 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E52-7 (SS1) - E7-17 (SSW1)
Always
Below 1 Ω
E52-2 (SS2) - E7-16 (SSW2)
Always
Below 1 Ω
E52-5 (GND) - Body ground
Always
Below 1 Ω
E52-7 (SS1) or E7-17 (SSW1) - Body ground
Always
10 kΩ or higher
E52-2 (SS2) or E7-16 (SSW2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
