2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION

Power is supplied to the radio and display assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E186459E11

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the radio and display assembly, steering pad switch assembly, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result:
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except radio and display assembly.
    B
    No illumination comes on (radio and display assembly, hazard switch, glove box, etc.).
    C
    (for 2AZ-FE)
    D
    (for 2GR-FE)



B
Go to step 6

C
GO TO LIGHTING SYSTEM (for 2AZ-FE) (Click here)

D
GO TO LIGHTING SYSTEM (for 2GR-FE) (Click here)
A


2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY)

  1. E120026E26
    Disconnect the E18 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E18-12 (IL+2) - Body ground
    Light control switch tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the a1 steering pad switch assembly connector.

  1. Connect a positive (+) lead from the battery to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.E187959E06

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.

    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch Assembly)
    -
    -



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E168547E15
    Disconnect the E18 spiral cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-5 (IL+2) - E18-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets below.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

Text in Illustration 
*1
Component without harness connected
(Spiral Cable Sub-assembly)
*2
Steering Pad Switch Side
*3
Vehicle Side


NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY ASSEMBLY)
  1. Disconnect the F8 radio and display assembly connector.

  1. Disconnect the E18 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F8-6 (SWG) - E18-4 (EAU)
    Always
    Below 1 Ω
    F8-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR
  1. Disconnect the F6 radio and display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F6-10 (ILL+) - Body ground
    Light control switch in tail or head
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Steering Pad Switch Circuit (from Jun 2009)Parking Brake Switch Circuit (from Jun 2009) →