2006-2011 Camry Aurion · Service Manual RESTRAINTS

Diagnosis Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.
DTCs are displayed by blinking of the SRS warning light.

HINT:
  1. When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.
  2. A DTC output mode signal is transmitted through CAN communication system to each ECU including the center airbag sensor assembly. Thus when all systems do not enter DTC output mode, there may be an ECM malfunction.


WIRING DIAGRAM

C142529E06

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    HINT:
    The center airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.
    Refer to the "Bus Check" for CAN communication system.
    1. Click here for LHD with Smart Entry and Start System
    1. Click here for LHD without Smart Entry and Start System
    2. Click here for RHD with Smart Entry and Start System
    1. Click here for RHD without Smart Entry and Start System


    Result:
    Condition
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2. CHECK WIRE HARNESS (TC OF DLC3 - TC OF ECM)

  1. E126838E21
    Turn the ignition switch off.

  1. Disconnect the connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for 2GR-FE LHD:
    Tester Connection
    Condition
    Specified Condition
    E10-13 (TC) - A55-27 (TC)
    Always
    Below 1 Ω
    for 2GR-FE RHD and 2AZ-FE:
    Tester Connection
    Condition
    Specified Condition
    E10-13 (TC) - A24-27 (TC)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE WIRE HARNESS (TC OF DLC3 - TC OF ECM)
OK


3. CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

  1. C126742E26
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE WIRE HARNESS (CG OF DLC3 - BODY GROUND)
OK


4. CHECK WIRE HARNESS (TC OF ECM - BODY GROUND)

  1. E126835E21
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for 2GR-FE LHD:
    Tester Connection
    Condition
    Specified Condition
    A55-27 (TC) - Body ground
    Always
    1 MΩ or higher
    for 2GR-FE RHD and 2AZ-FE:
    Tester Connection
    Condition
    Specified Condition
    A24-27 (TC) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    NG
    A
    OK (for 2GR-FE RHD)
    B
    OK (except 2GR-FE RHD)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU


← Diagnosis Circuit (Jun 2006 – Sep 2006)Diagnosis Circuit (from Jun 2009) →