2006-2011 Camry Aurion · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

NOTICE:
  1. When the automatic transaxle is replaced, the transaxle's compensation code must be input into the TCM (Click here).
  2. When the TCM is replaced, the existing transaxle compensation codes must be input into the new TCM (Click here).
  3. If the following parts have been replaced, initialize the TCM and perform a road test to allow the TCM to learn (Click here).
    1. Valve body assembly
    1. Shift solenoid SL3
    1. Shift solenoid SL4
  4. If the following parts have been replaced, perform a road test to allow the TCM to learn (Click here).
    1. Shift solenoid SL1
    1. Shift solenoid SL2
  5. If the TCM or transaxle has been replaced, register the transmission compensation code in the TCM (Click here).
  6. Perform RESET MEMORY (AT initialization) when replacing the automatic transmission assembly, engine assembly or ECM (Click here).


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

4. REMOVE FRONT WHEELS

5. REMOVE ENGINE UNDER COVER LH

6. REMOVE ENGINE UNDER COVER RH

7. REMOVE FRONT FENDER APRON SEAL RH

8. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.

    A128117E02

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


9. DRAIN AUTOMATIC TRANSAXLE FLUID

  1. C142572
    Remove the refill plug and gasket.

  1. C142571
    Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket.

  1. C142574
    Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube.

  1. Drain the automatic transaxle fluid.

  1. C142574
    Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }

  1. C142571
    Using a 6 mm socket hexagon wrench, install the overflow plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. C142572
    Install the refill plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


10. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Click here.


11. REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY

  1. C141972E01
    Disengage the clamp.

  1. Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.


12. REMOVE COOL AIR INTAKE DUCT SEAL

  1. A141576E01
    Remove the 7 clips and intake duct seal.


13. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A140800
    Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.


14. REMOVE V-RIBBED BELT

  1. A129622E01
    Using SST, release the belt tension by turning the belt tensioner counterclockwise, and remove the V-ribbed belt from the belt tensioner.
    SST
    09249-63010  

  1. A095070
    While turning the belt tensioner counterclockwise, align with its holes, and then insert a 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner.


15. REMOVE AIR CLEANER INLET ASSEMBLY

  1. A132969
    Remove the 2 bolts, clamp and air cleaner inlet.


16. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A135704
    Disconnect the 3 vacuum hoses.

  1. A135705E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the No. 2 ventilation hose (*2).

  1. Disconnect the hose band (*3).

  1. A135706
    Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.


17. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A132971
    Disconnect the vacuum hose and hose clamp.

  1. Remove the 3 bolts and air cleaner case.


18. REMOVE NO. 1 AIR CLEANER INLET

  1. A132970
    Remove the bolt and No. 1 air cleaner inlet.


19. REMOVE BATTERY

  1. A132972
    Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.


20. REMOVE INTAKE AIR RESONATOR SUB-ASSEMBLY

  1. A133928
    Remove the clip, bolt and intake air resonator.


21. REMOVE NO. 2 B ENGINE MOUNTING STAY RH

  1. A132985
    Remove the bolt, 2 nuts, and No. 2 B engine mounting stay RH.


22. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

  1. A132986
    Remove the 4 bolts and engine moving control rod.


23. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

  1. A132983E01
    Remove the clamp and disconnect the No. 1 fuel vapor feed hose.


24. DISCONNECT CHECK VALVE TO BRAKE BOOSTER HOSE
  1. Remove the clamp and disconnect the check valve to brake booster hose.


25. DISCONNECT RADIATOR INLET HOSE

  1. A146039
    Disconnect the radiator inlet hose from the radiator assembly.


26. DISCONNECT RADIATOR OUTLET HOSE

  1. A133364
    Disconnect the radiator outlet hose from the radiator assembly.


27. DISCONNECT NO. 1 OIL COOLER INLET HOSE

  1. A133365
    Disconnect the No. 1 oil cooler inlet hose from the radiator assembly.


28. DISCONNECT NO. 1 OIL COOLER OUTLET HOSE

  1. A133366
    Disconnect the No. 1 oil cooler outlet hose from the radiator assembly.


29. DISCONNECT HEATER WATER HOSE INLET

  1. A132978E01
    Disconnect the heater inlet water hose.


30. DISCONNECT HEATER WATER HOSE OUTLET
  1. Disconnect the heater outlet water hose.


31. REMOVE ECM

  1. A135711
    Remove the 3 nuts.

  1. A128952E01
    Disconnect the 2 connectors and remove the ECM.

  1. A135713
    Remove the 4 screws and 2 ECM brackets.


32. REMOVE RELAY BLOCK COVER UPPER

33. DISCONNECT ENGINE WIRE

  1. A132975
    Disconnect the engine wire from the engine room junction block.

    1. Remove the nut and separate the wire harness.

    2. Using a screwdriver, unlock the engine room junction block. Pull the engine room junction block upward.

    3. Disconnect the engine wire connectors.

  1. A132976
    Remove the 2 bolts and 2 clamps from the body.

  1. A132981
    Remove the bolt and clamp from the bracket.


34. SEPARATE WIRE HARNESS

  1. C096795
    Remove the bolt and disconnect the wire harness.


35. DISCONNECT CONNECTOR

  1. C132238
    Disconnect the park/neutral position switch connector.


36. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. A132973
    Remove the clip and nut, and separate the cable from the transaxle.


37. SEPARATE FUEL TUBE SUB-ASSEMBLY

  1. A129626
    Remove the No. 1 fuel pipe clamp.

  1. B012941E15
    Disconnect the connector from the tube while pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for contamination in the tube and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.


38. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

  1. A129629
    Disconnect the No. 1 oil reservoir to pump hose.


39. DISCONNECT RETURN TUBE SUB-ASSEMBLY

  1. A132984E01
    Disconnect the return tube sub-assembly.


40. REMOVE FRONT EXHAUST PIPE NO. 1 SUPPORT BRACKET

  1. A085549E01
    Remove the 2 nuts and front support brackets.


41. REMOVE EXHAUST FRONT PIPE ASSEMBLY
  1. Disconnect the 2 heated oxygen sensor (bank 1, 2 sensor 2) connectors.

  1. Remove the 2 nuts from the exhaust front pipe (left bank exhaust manifold side).

    A146046

  1. Remove the 2 bolts from the exhaust front pipe (right bank exhaust pipe manifold side).

  1. Remove the exhaust front pipe.

  1. Remove the 2 gaskets from the exhaust front pipe.


42. REMOVE FRONT AXLE HUB NUT LH

  1. C108168E02
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


43. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures as described for the LH side.


44. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

  1. C140591
    Remove the nut and separate the front stabilizer link assembly.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


45. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


46. SEPARATE FRONT SPEED SENSOR LH

  1. C140592
    Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.

  1. C132782E01
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.


47. SEPARATE FRONT SPEED SENSOR RH

HINT:
Use the same procedures as described for the LH side.


48. SEPARATE TIE ROD END SUB-ASSEMBLY LH

  1. C108515E05
    Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end sub-assembly from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Make sure that the string of SST is securely tied to the vehicle.
    2. Be careful not to damage the ball joint dust cover.
    3. Be careful not to damage the steering knuckle.
    4. Be careful not to damage the front disc brake dust cover.


49. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


50. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM LH

  1. F040142E01
    Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.


51. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures as described for the LH side.


52. SEPARATE FRONT AXLE ASSEMBLY LH

  1. D032030E06
    Put matchmarks on the front drive shaft assembly and the axle hub.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.


53. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures as described for the LH side.


54. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET
  1. Remove the bolt and No. 1 exhaust pipe support bracket.


55. REMOVE FLYWHEEL HOUSING UNDER COVER

  1. C135005
    Remove the 2 bolts, exhaust pipe support bracket and flywheel housing under cover.


56. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

  1. D002828
    Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.


57. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C133501
    Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.

  1. C156702E01
    Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.

  1. C156703E01
    Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.


58. REMOVE GENERATOR ASSEMBLY

  1. A133865
    Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. Disconnect the connector from the compressor and magnetic clutch.

  1. Disconnect the 2 wire harness clamps.

  1. A133866
    Remove the 2 bolts.

  1. A133867
    Remove the bolt from the cylinder block.

  1. Disconnect the wire harness clamp and remove the generator assembly.

  1. A128066
    Remove the bolt and wire harness clamp stay.

  1. A135391
    Remove the bolt and bracket.


59. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH
  1. Remove the 2 connector clamps.

  1. A132977
    Remove the 4 bolts and separate the compressor.

    HINT:
    Hang up the hoses instead of detaching them.


60. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine lifter.

  1. A129634
    Remove the 4 bolts, 2 nuts, and frame side rail plates RH and LH.

  1. Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.

  1. Operate the engine lifter, then remove the engine assembly from the vehicle.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.


61. REMOVE VANE PUMP ASSEMBLY
  1. Disconnect the power steering oil pressure switch connector.

  1. A138331E02
    Remove the pressure feed tube clamp bolt C.

  1. Loosen the bolt A.

  1. Remove the bolt B and vane pump.


62. INSTALL ENGINE HANGERS

  1. A129635E05
    Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 engine hanger 12281-31120
    No. 2 engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.


63. REMOVE FRONT FRAME ASSEMBLY

  1. A132990
    Disconnect the connector and clamp.

  1. A132989
    Disconnect the 2 clamps.

  1. A078403E05
    Remove the 2 nuts and disconnect the engine mounting insulators RH and LH.

  1. Disconnect the vacuum hose clamps from the resonator.

  1. A132988
    Remove the bolt and disconnect the engine mounting insulator FR.


64. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

  1. C083850E02
    Using SST, remove the front drive shaft assembly LH.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    2. Be careful not to drop the drive shaft assembly.


65. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

  1. C080304E03
    Using a screwdriver, remove the bearing bracket hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot and oil seal.


66. REMOVE ENGINE WIRE

67. REMOVE STARTER ASSEMBLY

  1. A133864
    Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Remove the 2 bolts and starter assembly.


68. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

  1. C142575E01
    Remove the bolt and breather bracket from the camshaft housing sub-assembly LH.

  1. Remove the breather hose from the breather bracket.

  1. C157088
    Remove the 11 bolts.

  1. Separate and remove the automatic transaxle.


69. REMOVE ENGINE MOUNTING FRONT BRACKET

  1. C133601
    Remove the 3 bolts and engine mounting front bracket.


70. REMOVE TCM

  1. C139840E01
    Remove the 2 bolts and TCM from the transaxle.


71. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

  1. C135002
    Remove the bolt and hole cover from the transaxle case.

  1. Remove the O-ring from the hole cover.


72. REMOVE WIRE HARNESS CLAMP BRACKET (for LHD)

  1. C139880
    Remove the 4 bolts and 4 clamp brackets.


73. REMOVE WIRE HARNESS CLAMP BRACKET (for RHD)

  1. C143321
    Remove the 5 bolts and 5 clamp brackets.


74. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

  1. C139615
    Remove the 2 bolts and No. 1 transmission control cable bracket.


75. SEPARATE OIL COOLER OUTLET HOSE

  1. C139881
    Separate the oil cooler outlet hose.


76. SEPARATE OIL COOLER INLET HOSE

  1. C139882
    Separate the oil cooler inlet hose.


77. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

  1. C157087
    Remove the torque converter clutch assembly from the automatic transaxle assembly.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Oct 2006 – May 2009) →