B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The front passenger side - side airbag sensor circuit consists of the center airbag sensor assembly, side airbag sensor LH, and rear airbag sensor LH.If the center airbag sensor assembly receives signals from the side airbag sensor LH and rear airbag sensor LH, it determines whether or not the SRS should be activated.
DTC B1625/22 is recorded when a malfunction is detected in the front passenger side - side airbag sensor circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1625/22 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.

Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor LH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor LH.
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor LH side) are not damaged.
- OK:
- The connectors are not deformed or damaged.
|
|
||||
| OK | |
| 4. CHECK FLOOR WIRE (OPEN) |
Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - N7-3 (BBL-)
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK FLOOR WIRE (SHORT) |
Disconnect the service wire from connector B.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - N7-3 (BBL-)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK FLOOR WIRE (SHORT TO B+) |
Connect the negative (-) terminal cable from the battery, and wait for at least 2 seconds.

Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - Body ground
Ignition switch ON
Below 1 V
N7-3 (BBL-) - Body ground
Ignition switch ON
Below 1 V
|
|
||||
| OK | |
| 7. CHECK FLOOR WIRE (SHORT TO GROUND) |
Turn the ignition switch to the LOCK position.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - Body ground
Always
1 MΩ or higher
N7-3 (BBL-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 8. CONFIRM PART NUMBER OF SIDE AIRBAG SENSOR |
Check that the part number of the side airbag sensor LH is equal to the number of the other side.
- OK:
- Those numbers are the same.
Connect the connectors to the center airbag sensor assembly and side airbag sensor LH.
|
|
||||
| OK | |
| 9. CHECK SIDE AIRBAG SENSOR LH |
Interchange the side airbag sensor RH with LH and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- Result:
Result
Proceed to
DTC B1620/21 and B1625/22 are not output.
A
DTC B1625/22 is output.
B
DTC B1620/21 is output.
C
- HINT:
- Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
| A | ||
| ||
| 10. REPLACE SIDE AIRBAG SENSOR LH |
Replace the side airbag sensor LH (Click here).

- HINT:
- Perform inspection using parts from a normal vehicle if possible.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
|
|
||||
| NG | |
| 11. CHECK CONNECTION OF CONNECTOR |
Check that the connector is properly connected to the rear airbag sensor LH.
- OK:
- The connector is properly connected.
|
|
||||
| OK | |
| 12. CHECK CONNECTOR |
Disconnect the connector from the rear airbag sensor LH.
Check that the connector (on the rear airbag sensor LH side) is not damaged.
- OK:
- The connector is not deformed or damaged.
|
|
||||
| OK | |
| 13. CHECK FLOOR WIRE (OPEN) |
Disconnect the connector from the side airbag sensor LH.
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - N7-2 (BCL-)
Always
Below 1 Ω
|
|
||||
| OK | |
| 14. CHECK FLOOR WIRE (SHORT) |
Disconnect the service wire from connector C.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - N7-2 (BCL-)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 15. CHECK FLOOR WIRE (SHORT TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - Body ground
Ignition switch ON
Below 1 V
N7-2 (BCL-) - Body ground
Ignition switch ON
Below 1 V
|
|
||||
| OK | |
| 16. CHECK FLOOR WIRE (SHORT TO GROUND) |
Turn the ignition switch to the LOCK position.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - Body ground
Always
1 MΩ or higher
N7-2 (BCL-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 17. CHECK REAR AIRBAG SENSOR LH |
Connect the connector to the side airbag sensor LH.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
|
|
||||
| OK | |
| 18. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch to the LOCK position.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connector to the rear airbag sensor LH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
