B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The front passenger side - side airbag sensor circuit consists of the center airbag sensor assembly, side airbag sensor (passenger side), and rear airbag sensor (passenger side).If the center airbag sensor assembly receives signals from the side airbag sensor (passenger side) and rear airbag sensor (passenger side), it determines whether or not the SRS should be activated.
DTC B1625/22 is recorded when a malfunction is detected in the front passenger side - side airbag sensor circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1625/22 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC |
Turn the ignition switch on (IG), and wait for at least 60 seconds.

Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (passenger side).
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (passenger side).
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (passenger side) side) are not damaged.
- OK:
- The connectors are not deformed or damaged.
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK WIRE HARNESS (OPEN) |
Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-4 (BBR+) - O7-3 (BBR-)
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - N7-3 (BBL-)
Always
Below 1 Ω
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK WIRE HARNESS (SHORT) |
Disconnect the service wire from connector B.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-4 (BBR+) - O7-3 (BBR-)
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - N7-3 (BBL-)
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 6. CHECK WIRE HARNESS (SHORT TO B+) |
Connect the negative (-) terminal cable from the battery, and wait for at least 2 seconds.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-4 (BBR+) - Body ground
Ignition switch on (IG)
Below 1 V
O7-3 (BBR-) - Body ground
Ignition switch on (IG)
Below 1 V
- for RHD:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - Body ground
Ignition switch on (IG)
Below 1 V
N7-3 (BBL-) - Body ground
Ignition switch on (IG)
Below 1 V
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 7. CHECK WIRE HARNESS (SHORT TO GROUND) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-4 (BBR+) - Body ground
Always
1 MΩ or higher
O7-3 (BBR-) - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
N7-4 (BBL+) - Body ground
Always
1 MΩ or higher
N7-3 (BBL-) - Body ground
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 8. CONFIRM PART NUMBER OF SIDE AIRBAG SENSOR |
Check that the part number of the side airbag sensor (passenger side) is equal to the number of the other side.
- OK:
- Those numbers are the same.
Connect the connectors to the center airbag sensor assembly and side airbag sensor (passenger side).
|
|
||||
| OK | |
| 9. CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE) |
Interchange the side airbag sensor (driver side) with side airbag sensor (passenger side) and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- Result:
Result
Proceed to
DTC B1620/21 and B1625/22 are not output.
A
DTC B1625/22 is output.
B
DTC B1620/21 is output.
C
- HINT:
- Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor (driver side) and side airbag sensor (passenger side) to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
| A | ||
| ||
| 10. REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE) |
Replace the side airbag sensor (passenger side) (Click here).

- HINT:
- Perform inspection using parts from a normal vehicle if possible.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
|
|
||||
| NG | |
| 11. CHECK CONNECTION OF CONNECTOR |
Check that the connector is properly connected to the rear airbag sensor (passenger side).
- OK:
- The connector is properly connected.
|
|
||||
| OK | |
| 12. CHECK CONNECTOR |
Disconnect the connector from the rear airbag sensor (passenger side).
Check that the connector (on the rear airbag sensor (passenger side) side) is not damaged.
- OK:
- The connector is not deformed or damaged.
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
| OK | |
| 13. CHECK WIRE HARNESS (OPEN) |
Disconnect the connector from the side airbag sensor (passenger side).
Using a service wire, connect terminals 2 and 1 of connector C.

- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-1 (BCR+) - O7-2 (BCR-)
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - N7-2 (BCL-)
Always
Below 1 Ω
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 14. CHECK WIRE HARNESS (SHORT) |
Disconnect the service wire from connector C.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-1 (BCR+) - O7-2 (BCR-)
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - N7-2 (BCL-)
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 15. CHECK WIRE HARNESS (SHORT TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-1 (BCR+) - Body ground
Ignition switch on (IG)
Below 1 V
O7-2 (BCR-) - Body ground
Ignition switch on (IG)
Below 1 V
- for RHD:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - Body ground
Ignition switch on (IG)
Below 1 V
N7-2 (BCL-) - Body ground
Ignition switch on (IG)
Below 1 V
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 16. CHECK WIRE HARNESS (SHORT TO GROUND) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O7-1 (BCR+) - Body ground
Always
1 MΩ or higher
O7-2 (BCR-) - Body ground
Always
1 MΩ or higher
- for LHD:
Tester Connection
Condition
Specified Condition
N7-1 (BCL+) - Body ground
Always
1 MΩ or higher
N7-2 (BCL-) - Body ground
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 17. CHECK REAR AIRBAG SENSOR (PASSENGER SIDE) |
Connect the connector to the side airbag sensor (passenger side).

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
|
|
||||
| OK | |
| 18. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connector to the rear airbag sensor (passenger side).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.
- Result:
Result
Proceed to
OK
A
NG (for 2GR-FE RHD)
B
NG (except 2GR-FE RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
