Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter
Circuit diagnosis · Vehicles built from Jun 2009
DESCRIPTION
This circuit is necessary for the ASL (Automatic Sound Levelizer) built into the radio and display assembly.Speed signals are received from the combination meter assembly and used for the ASL.
The ASL function automatically adjusts the sound data in order to enable to hear the clear audio sound even when vehicle noise increases (as vehicle noise increases, the volume is increased etc.).
- HINT:
- A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
- If a short occurs in an ECU, all systems in the diagram below will not operate normally.
- A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
WIRING DIAGRAM
| for 2GR-FE |


| for 2AZ-FE |


INSPECTION PROCEDURE
| 1. CONFIRM MODEL |
- Result:
Result
Proceed to
for 2GR-FE
A
for 2AZ-FE
B
|
|
||||
| A | |
| 2. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM) |
Check the output waveform.

Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal F2-12 (+S) and body ground.
Turn the ignition switch on (IG).
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
Item
Condition
Measurement terminal
F2-12 (+S) - Body ground
Tool setting
5 V/DIV., 20 ms./DIV.
Vehicle condition
Wheel being rotated
- OK:
- The waveform is similar to that shown in the illustration.
- HINT:
- When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
Text in Illustration *1
Component with harness connected
(Combination Meter Assembly)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - COMBINATION METER ASSEMBLY) |
Disconnect the F8 radio and display assembly connector.
Disconnect the F2 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F8-3 (SPD) - F2-12 (+S)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - NO. 3 JUNCTION BLOCK) |
Disconnect the 3T No. 3 junction block connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F8-3 (SPD) - 3T-9
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 5. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM) |
Check the input waveform.

Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal F1-11 (+S) and body ground.
Turn the ignition switch on (IG).
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
Item
Condition
Measurement terminal
F1-11 (+S) - Body ground
Tool setting
5 V/DIV., 20 ms./DIV.
Vehicle condition
Wheel being rotated
Text in Illustration *1
Component with harness connected
(Combination Meter Assembly)
- OK:
- The waveform is similar to that shown in the illustration.
- HINT:
- When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - COMBINATION METER ASSEMBLY) |
Disconnect the F8 radio and display assembly connector.
Disconnect the F1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F8-3 (SPD) - F1-11 (+S)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - NO. 3 JUNCTION BLOCK) |
Disconnect the 3T No. 3 junction block connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F8-3 (SPD) - 3T-9
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
