REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
REMOVE BRAKE BOOSTER ASSEMBLY |
 |
- HINT:
- Refer to the procedures up to "REMOVE BRAKE BOOSTER". (Click here)
| 2.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 3.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
 |
- Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 4.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (except 2GR-FE RHD)
|
 |
- Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.
| 5.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for 2GR-FE RHD)
|
 |
- Remove the bolt <D> and the screw <F>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect each connector, and then remove the lower No. 1 instrument panel finish panel.
| 6.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
|
 |
- Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the No. 1 instrument panel sub-assembly.
| 7.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for 2AZ-FE RHD)
|
 |
- Disengage the 3 claws and the 2 clips.
Disconnect the connector and remove the No. 1 instrument panel sub-assembly.
| 8.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for 2GR-FE RHD)
|
 |
- Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the No. 1 instrument panel sub-assembly.
| 9.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)
|
 |
- Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
| 10.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)
|
 |
- Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
Disconnect the connector.
| 11.
REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
|
 |
- Remove the 2 clips.
Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.
| 12.
REMOVE COMBINATION METER ASSEMBLY
|
 |
Using the tilt and telescopic functions, fully lower and extend the steering wheel.
- Remove the 4 screws.
Disconnect the connector.
- Remove the combination meter assembly as shown in the illustration.
| 13.
REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for LHD) |
 |
- Disconnect the stop light switch connector and disengage the 2 clamps.
- Remove 2 bolts (A), bolt (B) and the No. 1 brake pedal support plate.
- Remove the bolt and the brake pedal support assembly.
| 14.
REMOVE HEADLIGHT LEVELING ECU ASSEMBLY (w/ Headlight Leveling)
|
 |
- Disconnect the connector.
Remove the bolt and the headlight leveling ECU assembly.
| 15.
REMOVE AFS ECU (w/ AFS)
|
 |
- Disconnect the connector.
Remove the bolt and the AFS ECU.
| 16.
REMOVE ACCELERATOR PEDAL ASSEMBLY (for RHD)
|
 |
- Disconnect the accelerator pedal connector.
Remove the 2 bolts and the accelerator pedal assembly.
| 17.
REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for RHD) |
 |
- Disconnect the stop light switch connector.
- Remove 2 bolts (A), bolt (B) and the No. 1 brake pedal support plate.
- Remove the bolt and brake pedal support assembly, and disengage the clamp.