2006-2011 Camry Aurion · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE BRAKE BOOSTER ASSEMBLY

HINT:
Refer to the procedures up to "REMOVE BRAKE BOOSTER" (Click here).


2. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


3. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (except 2GR-FE RHD)

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


5. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for 2GR-FE RHD)

  1. B158913E01
    Remove the bolt <D> and the screw <F>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect each connector, and then remove the lower No. 1 instrument panel finish panel.


6. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (except 2GR-FE RHD)

  1. B149938
    Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the No. 1 instrument panel sub-assembly.


7. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for 2GR-FE RHD)

  1. B158916
    Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the No. 1 instrument panel sub-assembly.


8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)

  1. B144612
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.


9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)

  1. B159330
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.

  1. Disconnect the connector.


10. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133985E01
    Remove the 2 clips.

  1. Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.


11. REMOVE COMBINATION METER ASSEMBLY
  1. Using the tilt and telescopic functions, fully lower and extend the steering wheel.

  1. E136754
    Remove the 4 screws.

  1. Disconnect the connector.

  1. E128009
    Remove the combination meter assembly as shown in the illustration.


12. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for LHD)

  1. C132710E01
    Disconnect the stop light switch connector and disengage the 2 clamps.

  1. C132711E01
    Remove 2 bolts (A), bolt (B) and the No. 1 brake pedal support plate.

  1. C132712
    Remove the bolt and the brake pedal support assembly.


13. REMOVE AFS ECU (w/ AFS)

  1. E141435
    Disconnect the connector.

  1. Remove the bolt and the AFS ECU.


14. REMOVE ACCELERATOR PEDAL ASSEMBLY (for RHD)

  1. A135676
    Disconnect the accelerator pedal connector.

  1. Remove the 2 bolts and the accelerator pedal assembly.


15. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY (for RHD)

  1. C133309
    Disconnect the stop light switch connector.

  1. C132837E02
    Remove 2 bolts (A), bolt (B) and the No. 1 brake pedal support plate.

  1. C132836E02
    Remove the bolt and brake pedal support assembly, and disengage the clamp.

← REMOVAL (Oct 2006 – May 2009)DISASSEMBLY (from Jun 2006) →