2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshooting · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

NOTICE:
  1. DTCs for the CAN communication system are as follows: U0073, U0100, U0122, U0123, U0124, U0126, U1101, U0140, B2427, U1002, U0182 (*1), B1207, B1297, B1276 (*1), B1272 (*1), and B2326.
    *1: with Seat position memory
  2. Refer to troubleshooting of each system if DTCs regarding the CAN communication system are not output.
  3. If DTC B1201, Mayday ECU Communication Stop Mode, is output, inspect the mayday ECU power source circuit and its CAN branch wire. Refer to the mayday system repair manual for details.


1.CHECK AND CLEAR DTCS

    HINT:
    1. CAN communication DTCs are output when there is an open or short in any of the communication wires. Any problems with the power source of a corresponding ECU or sensor, or problems in the ECU or the sensor itself also cause these DTCs to be output.
    2. If a CAN communication wire connector is disconnected with the engine switch on (IG), the ECUs of the corresponding system and related systems record a DTC.

NEXT

2.CHECK FOR INSTALLED SYSTEMS (ECUS & SENSORS) THAT ADOPT CAN COMMUNICATION
  1. Check which of the following is adopted: Adaptive front-lighting system, Seat position memory system (Click here).

NEXT

3.CHECK WITH INTELLIGENT TESTER
  1. Using the intelligent tester, display the "Communication Bus Check" screen (Click here).

  2. Observe the screen for approximately 1 minute to check the ECUs and sensors displayed on the screen.

    Result:
    Symptom
    Proceed to
    All ECUs and sensors connected to the CAN communication system are not displayed on the screen.
    (Open in CAN No. 1 bus main wire, short in CAN No. 1 bus wire, or DLC3 branch wire malfunction)
    A
    One of the ECUs and sensors connected to the CAN communication system is not displayed on the screen.
    (Open in ECU or sensor branch wires, or communication interrupted)
    B(*1)
    Some of the ECUs and sensors connected to the CAN communication system are not displayed on the screen. During this check, some ECUs and sensors repeatedly appear and disappear from the screen.
    (Open in one side of ECU or sensor branch wires)
    C
    1. All ECUs and sensors except the main body ECU connected to the CAN MS bus are not displayed on the screen.
    2. The main body ECU outputs DTC B2326.
    (Open in CAN MS bus main wire or short in CAN MS bus wire)
    D
    All ECUs and sensors connected to the CAN MS bus are not displayed on the screen.
    (Open in main body ECU branch wire or main body ECU malfunction)
    E
    1. All ECUs and sensors except the gateway ECU connected to the CAN No. 2 bus are not displayed on the screen.
    2. The gateway ECU outputs DTC U1002.
    (Open in CAN No. 2 bus main wire or short in CAN No. 2 bus wire)
    F
    All ECUs and sensors connected to the CAN No. 2 bus are not displayed on the screen.
    (Open in gateway ECU branch wire or gateway ECU malfunction)
    G
    All ECUs and sensors connected to the CAN communication system are displayed on the screen.
    (CAN bus circuit is currently normal)
    H

    NOTICE:
    1. The systems (ECUs, sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs, sensors) are installed on the vehicle (Click here).
    2. Non-installed ECUs or sensors will not be displayed. Do not mistake them for being in the communication stop mode.
    3. The ECUs and sensors that repeatedly appear and disappear from the screen during this check are considered normal. (The response to the intelligent tester and the tester display are affected by signals output from other ECUs which have an open circuit in either of their CAN branch wires.)
    4. If only ECT is not displayed, check DTC U0101 of the SFI system (Click here).

    HINT:
    1. (*1): See the "DTC CHART" instead of the "COMMUNICATION STOP MODE TABLE", when some of the ECUs connected to the CAN MS bus or the CAN No. 2 bus are not displayed on the screen (Click here).
    2. The ECUs connected to the CAN MS bus are displayed on the screen by the main body ECU.
    3. The ECUs connected to the CAN No. 2 bus are displayed on the screen by the gateway ECU.
    4. If communication stops between an ECU and the CAN No. 2 bus, the ECU will not be displayed on the intelligent tester screen.


B.

C.

D.

E.

F.

G.

H.
A

4.CHECK CAN NO. 1 BUS WIRE
  1. Check the CAN No. 1 bus wire (Click here).

    HINT:
    If the area where an open or short is occurring in a CAN No. 1 bus wire can be determined, refer to the "PROBLEM SYMPTOMS TABLE" (Click here).


NEXT.
5.RECHECK DTC

    HINT:
    1. Sometimes CAN communication system DTCs are output, but all the ECUs and sensors connected to the CAN communication system are displayed on the intelligent tester. In this case, previous or history DTCs may indicate the cause of the problem.
    2. ECUs related to a problem in the CAN No. 1 bus will store DTCs to indicate communication malfunctions. The communication stop mode in the CAN No. 1 bus can be determined by comparing the combination of DTCs that have been set. Refer to the DTC combination table for the CAN No. 1 bus.
    3. The main body ECU will store communication error DTCs when the ECUs connected to the CAN MS bus cannot communicate, or if a network malfunction occurs.
    4. The gateway ECU will store communication error DTCs when the ECUs connected to the CAN No. 2 bus cannot communicate, or if a network malfunction of the CAN No. 2 bus occurs.


    Result:
    Result
    Proceed to
    Communication error DTCs other than the codes output from the main body ECU and the gateway ECU are output. (A malfunction occurred in the CAN No. 1 bus)
    A
    The main body ECU outputs CAN MS DTC B2326. (A malfunction occurred in the CAN MS bus)
    B
    The main body ECU outputs DTCs other than CAN MS bus DTC B2326. (A malfunction occurred in an ECU branch wire connected to the CAN MS bus)
    C
    The gateway ECU outputs network trouble code U1002. (A malfunction occurred in the CAN No. 2 bus)
    D
    The gateway ECU outputs DTCs other than network trouble code U1002. (A malfunction occurred in an ECU branch wire connected to the CAN No. 2 bus)
    E


B.

C.

D.

E.
A

6.DTC COMBINATION TABLE
  1. Confirm trouble according to the combination of output DTCs regarding the CAN communication system (Click here).

    HINT:
    Previous CAN communication system DTCs may be the cause if CAN communication system DTCs are output and all ECUs and sensors connected to the CAN communication system are displayed on the intelligent tester's "Communication Bus Check" screen.

NEXT

7.CIRCUIT INSPECTION
    NEXT

    8.IDENTIFICATION OF PROBLEM
      NEXT

      9.REPAIR OR REPLACE
        NEXT

        10.CONFIRMATION TEST
          NEXT

          ← SYSTEM DESCRIPTION (from Jun 2009)HOW TO PROCEED WITH TROUBLESHOOTING (from Jun 2009) →