2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B2325 LIN Communication Bus Malfunction

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The main body ECU (Instrument panel junction block assembly) monitors communication between all the ECUs connected to the door system LIN bus lines. When the main body ECU (Instrument panel junction block assembly) detects errors in communication with all the ECUs connected to the door system LIN bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be output.
DTC No.
DTC Detection Condition
Trouble Area
B2325
Main body ECU (Instrument panel junction block assembly) detects errors in communication with the ECUs connected to the door system LIN bus lines 3 times in a row.
  1. Sliding roof ECU (Sliding roof drive gear)*
  2. Power window regulator motor (Driver side)
  3. Main body ECU (Instrument panel junction block assembly)
  4. Wire harness or connector

HINT:
*: Models with Sliding Roof System


WIRING DIAGRAM

B178898E07

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.


1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

  1. Disconnect the E8, Q12*1 and I5*2 or H10*3 connectors.

    HINT:
    1. *1: Models with Sliding Roof System
    2. *2: for LHD
    3. *3: for RHD

    B178900E04

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - Q12-4 (MPX1)*1
    Always
    Below 1 Ω
    E8-10 (LIN2) - I5-9 (LIN)*2
    Always
    Below 1 Ω
    E8-10 (LIN2) - H10-9 (LIN)*3
    Always
    Below 1 Ω
    E8-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. *1: Models with Sliding Roof System
    2. *2: for LHD
    3. *3: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result:
    Result
    Proceed to
    Models with Sliding Roof System
    A
    Models without Sliding Roof System
    B



B
Go to step 5
A


3. CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR))
  1. Connect the E8 and I5*1 or H10*2 connectors.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2325 is output
    A
    B2325 is not output
    B



B
Go to step 6
A


4. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE))
  1. Connect the Q12 connector.

  1. Disconnect the I5*1 or H10*2 connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2325 is output
    A
    B2325 is not output
    B



B
Go to step 8
A

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

5. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE))
  1. Connect the E8 connector.

  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2325 is output
    A
    B2325 is not output
    B



B
Go to step 8
A

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

6. REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR)
  1. Replace the sliding roof ECU (Sliding roof drive gear) with a normally-functioning or a new one (Click here).


NEXT


7. CHECK DTC OUTPUT
  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2325 is not output
    A
    B2325 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
A

END (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR) IS DEFECTIVE)

8. REPLACE POWER WINDOW REGULATOR MOTOR (DRIVER SIDE)
  1. Replace the power window regulator motor (Driver side) with a normally-functioning or a new one (Click here).


NEXT


9. CHECK DTC OUTPUT
  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2325 is not output
    A
    B2325 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
A

END (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) IS DEFECTIVE)


← B2321 Driver Side Door ECU Communication Stop (from Jun 2009)B2325 LIN Communication Bus Malfunction (Oct 2006 – May 2009) →