B2325 LIN Communication Bus Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The main body ECU (Instrument panel junction block assembly) monitors communication between all the ECUs connected to the door system LIN bus lines. When the main body ECU (Instrument panel junction block assembly) detects errors in communication with all the ECUs connected to the door system LIN bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be output.| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2325 |
Main body ECU (Instrument panel junction block assembly) detects errors in communication with the ECUs connected to the door system LIN bus lines 3 times in a row. |
|
- HINT:
- *: Models with Sliding Roof System
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the ignition switch off to troubleshoot:
- Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.
| 1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU) |
Disconnect the E8, Q12*1 and I5*2 or H10*3 connectors.
- HINT:
- *1: Models with Sliding Roof System
- *2: for LHD
- *3: for RHD
- *1: Models with Sliding Roof System


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E8-10 (LIN2) - Q12-4 (MPX1)*1
Always
Below 1 Ω
E8-10 (LIN2) - I5-9 (LIN)*2
Always
Below 1 Ω
E8-10 (LIN2) - H10-9 (LIN)*3
Always
Below 1 Ω
E8-10 (LIN2) - Body ground
Always
10 kΩ or higher
- HINT:
- *1: Models with Sliding Roof System
- *2: for LHD
- *3: for RHD
- *1: Models with Sliding Roof System
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E8-10 (LIN2) - Body ground
Always
Below 1 V
|
|
||||
| OK | |
| 2. SYSTEM CHECK |
Check the vehicle specifications.
- Result:
Result
Proceed to
Models with Sliding Roof System
A
Models without Sliding Roof System
B
|
|
||||
| A | |
| 3. CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR)) |
Connect the E8 and I5*1 or H10*2 connectors.
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Recheck for DTC (Click here).
- Result:
Result
Proceed to
B2325 is output
A
B2325 is not output
B
|
|
||||
| A | |
| 4. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE)) |
Connect the Q12 connector.
Disconnect the I5*1 or H10*2 connector.
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Recheck for DTC (Click here).
- Result:
Result
Proceed to
B2325 is output
A
B2325 is not output
B
|
|
||||
| A | ||
| ||
| 5. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE)) |
Connect the E8 connector.
Recheck for DTC (Click here).
- Result:
Result
Proceed to
B2325 is output
A
B2325 is not output
B
|
|
||||
| A | ||
| ||
| 6. REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR) |
Replace the sliding roof ECU (Sliding roof drive gear) with a normally-functioning or a new one (Click here).
| NEXT | |
| 7. CHECK DTC OUTPUT |
Recheck for DTC (Click here).
- Result:
Result
Proceed to
B2325 is not output
A
B2325 is output
B
|
|
||||
| A | ||
| ||
| 8. REPLACE POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) |
Replace the power window regulator motor (Driver side) with a normally-functioning or a new one (Click here).
| NEXT | |
| 9. CHECK DTC OUTPUT |
Recheck for DTC (Click here).
- Result:
Result
Proceed to
B2325 is not output
A
B2325 is output
B
|
|
||||
| A | ||
| ||
