2007 Aurion TRD · Service Manual Parking Brake

Parking Brake System

Parking Brake

PROBLEM SYMPTOMS TABLE
Use the table below to help determine the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary, replace these parts.
Symptom
Suspected Area
See page
Brake drag
1. Parking brake pedal travel (Out of adjustment)
Click Here
2. Parking brake cable (Sticking) [No. 1 cable]
Click Here
3. Parking brake cable (Sticking) [No. 2 / No. 3 cable]
4. Parking brake shoe clearance (Out of adjustment)
Click Here
5. Parking brake shoe lining (Cracked or distorted)
Click Here
ADJUSTMENT
HINT:
• Use the same procedures for the RH side and the LH side.
• The procedures listed below are for the LH side.
1. REMOVE REAR WHEEL
2. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
(a) Remove the 2 bolts and separate the rear disc brake caliper assembly.
HINT:
• Do not disconnect the flexible hose.
• Do not remove the brake pads.
• Do not allow the brake caliper to hang on the flexible hose. Always support the brake caliper.
-
3. REMOVE REAR DISC
(a) Release the parking brake and put matchmarks on the rear disc and the axle hub.
-
(b) Remove the rear disc.
HINT:
• If the rear disc is difficult to remove, rotate the disc while removing.
• If the rear disc jams, return the disc to its original position, remove the adjusting hole plug and turn the shoe adjusting nut in the clockwise direction to contract the parking brake shoe.
-
4. INSPECT PARKING BRAKE SHOE DIAMETER
(a) Measure the brake shoe diameter as shown in the illustration.
Standard:
189.55 mm (7.46 in.) Min.
189.75 mm (7.47 in.) Max.
-
5. ADJUST PARKING BRAKE SHOE DIAMETER
(a) If the shoe diameter is not within specification, adjust it by turning the adjusting nut.
-
(b) The gap between the adjusting nut and screw must not exceed 5 mm.
HINT:
• If the gap is 5 mm and the shoe diameter is less than specified, replace the parking brake shoe assembly.
• If the lining thickness is less than 1.5 mm or exhibits uneven wear, replace the parking brake shoe assembly.
-
6. INSTALL REAR DISC
(a) Align the matchmarks and install the rear disc.
-
(b) Install the adjusting hole plug, if removed.
-
7. INPSECT FOR PARKING BRAKE SHOE DRAG
(a) Apply and release the parking brake pedal several times.
-
(b) Spin the rear disc and ensure there is no drag from the parking brake shoe.
HINT:
If drag is present, remove the rear disc, measure and readjust the parking brake shoe diameter. Reinstall the rear disc and recheck for drag.
-
8. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
(a) Install the rear disc brake caliper assembly with the 2 bolts.
Torque:
62 N*m (632 kgf*cm, 46 ft.*lbf)
-
9. INSTALL REAR WHEEL
10. INSPECT PARKING BRAKE PEDAL TRAVEL
(a) Fully depress the parking brake pedal and release it to engage the parking brake.
-
(b) Fully depress the pedal again, and release it to disengage the parking brake.
-
(c) Slowly depress the parking brake pedal to the floor, and count the number of clicks.
Parking brake pedal travel:
7 to 10 notches at 300 N (31 kgf, 68 lbf)
-
11. ADJUST PARKING BRAKE PEDAL TRAVEL
(a) Depress the parking brake pedal.
-
(b) Hold the No. 1 wire adjusting nut using a wrench and loosen the lock nut.
-
(c) Release the parking brake pedal.
-
(d) Turn the No. 1 wire adjusting nut until the parking brake pedal travel meets the above specification.
-
(e) Hold the No. 1 wire adjusting nut using a wrench or an equivalent tool and tighten the lock nut.
Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)
-
(f) Count the number of clicks after depressing and releasing the parking brake pedal 3 or 4 times.
-
(g) Check if the parking brake drags.
-
(h) When operating the parking brake pedal, check the parking brake indicator light illuminates.
-