2007 Aurion TRD · Service Manual Lighting

FOG Light Assembly

Lighting

COMPONENTS
REMOVAL
1. REMOVE COOL AIR INTAKE DUCT SEAL ( Click Here )
2. REMOVE FRONT BUMPER ASSEMBLY ( Click Here )
3. REMOVE FOG LIGHT ASSEMBLY
(a) Remove the 3 screws and the fog light assembly.
-
DISASSEMBLY
1. REMOVE FOG LIGHT BULB
(a) Remove the fog light bulb as shown in the illustration.
-
2. REMOVE FOG LIGHT BRACKET
(a) Remove the 2 screws and the fog light bracket.
-
ADJUSTMENT
HINT:
It is possible that an incorrectly bulb can effect fog light aim. Bulb installation should be checked prior to performing the adjustment procedure.
1. VEHICLE PREPARATION FOR FOG LIGHT AIM ADJUSTMENT
(a) Prepare the vehicle:
• Ensure there is no damage or deformation to the body around the fog lights.
• Fill the fuel tank.
• Ensure the oil is filled to the specified level.
• Ensure the engine coolant is filled to the specified level.
• Inflate the tyres to the correct pressure.
• Unload the luggage compartment and vehicle, ensuring the spare tyre, tools, and jack are in their original positions.
• Sit a person of average weight (75 kg) in the driver's seat.
-
2. PREPARATION FOR FOG LIGHT AIMING
(a) Prepare the vehicle:
• Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
• Place the vehicle at a 90˚ angle to the wall.
• Create a 25 m (82 ft) distance between the vehicle (fog light bulb centre) and the wall.
• Ensure the vehicle is on a level surface.
• Bounce the vehicle up and down to settle the suspension.
-
(b) Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width) to use as a screen.
-
(c) Draw a vertical line down the centre of the screen (V line).
-
(d) Set the screen as shown in the illustration.


HINT:
• Stand the screen perpendicular to the ground.
• Align the V line on the screen with the centre of the vehicle.
-
(e) Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
HINT:
Mark the fog light bulb centre marks on the screen. If the centre mark cannot be observed on the fog light, use the centre of the fog light bulb or the manufacturer's name marked on the fog light as the centre mark.
(1) H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the centre marks. The H line should be at the same height as the fog light bulb centre marks of the fog lights.
(2) V LH Line, V RH Line (Centre mark position of left-hand (LH) and right-hand (RH) fog lights):
Draw two vertical lines so they intersect the H line at each centre mark.
-
3. FOG LIGHT AIMING INSPECTION
(a) Cover or disconnect the fog light on the opposite side to prevent its light affecting the fog light aiming inspection.
NOTICE:
Do not keep the fog light covered for more than 3 minutes.
-
(b) Start the engine.
-
(c) Turn on the fog light and check if the cut off line falls within the specified area in the following illustration.


-
4. FOG LIGHT AIMING ADJUSTMENT
(a) Adjust the aim vertically:
Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.
NOTICE:
The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so the final turn of the screw is in the clockwise direction.
HINT:
If it is not possible to correctly adjust fog light aim, check bulb, fog light unit, and fog light unit reflector installation.
-
REASSEMBLY
1. INSTALL FOG LIGHT BRACKET
(a) Install the fog light bracket with the 2 screws.
-
2. INSTALL FOG LIGHT BULB
(a) Install the fog light bulb as shown in the illustration.
-
INSTALLATION
1. INSTALL FOG LIGHT ASSEMBLY
(a) Install the fog light assembly with the 3 screws.
-
2. INSTALL FRONT BUMPER ASSEMBLY ( Click Here )
3. INSTALL COOL AIR INTAKE DUCT SEAL ( Click Here )
4. VEHICLE PREPARATION FOR FOG LIGHT AIM ADJUSTMENT ( Click Here )
5. PREPARATION FOR FOG LIGHT AIMING ( Click Here )
6. FOG LIGHT AIMING INSPECTION ( Click Here )
7. FOG LIGHT AIMING ADJUSTMENT ( Click Here )