Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
  1. Use the following procedure to troubleshoot the engine immobiliser system.
  1. *: Use the intelligent tester.



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS

      HINT:
      1. When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

      1. The following 5 items are important points in the problem analysis:

        What
        Vehicle model, system name
        When
        Date, time, occurrence frequency
        Where
        Road conditions
        Under what conditions?
        Driving conditions, weather conditions
        How did it happen?
        Problem symptoms

    NEXT


    3.INSPECT BATTERY VOLTAGE
    1. Measure the battery voltage.

      Standard Voltage:
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


    NEXT


    4.TURN ENGINE SWITCH ON (IG)

      NEXT


      5.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
      1. Use the intelligent tester to check if the CAN communication system is functioning normally.

        Result:
        Result
        Proceed to
        ECU is connected, communication line is normal
        A
        ECU is connected, communication line is malfunctioning (for LHD)
        B
        ECU is connected, communication line is malfunctioning (for RHD)
        C



      B.
      GO TO CAN COMMUNICATION SYSTEM (Click here)

      C.
      GO TO CAN COMMUNICATION SYSTEM (Click here)
      A


      6.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
      1. Use the intelligent tester to check if the LIN communication system is functioning normally.

        Result:
        Result
        Proceed to
        No DTC is output
        A
        DTC is output
        B



      B.
      GO TO LIN COMMUNICATION SYSTEM (Click here)
      A


      7.CHECK FOR DTCS (ENTRY AND START SYSTEM)*
      1. Check for DTCs and note any codes that are output.

      2. Clear the DTCs (Click here).

      3. Recheck for DTCs. Based on the DTCs output above, try to duplicate the engine immobiliser system DTC or steering lock system DTC by simulating the symptoms indicated by the DTCs.

        Result:
        Result
        Proceed to
        No DTCs are output
        A
        Steering lock system DTC is output (DTC B2781, B2782 or B2788)
        B
        Engine immobiliser system DTC is output (except DTC B2781, B2782 and B2788)
        C



      B.
      GO TO STEERING LOCK SYSTEM (Click here)

      C.
      GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
      A


      8.CHECK FOR DTCS (SFI SYSTEM)*
      1. Clear the DTCs (Click here).

      2. Recheck for DTCs.

        HINT:
        The DTCs for the engine immobiliser system are specified above. If other codes are output, check the DTC chart for the SFI system.

        Result:
        Result
        Proceed to
        No DTCs are output
        A
        Engine immobiliser system DTC is output (DTC B2799, B279A or B279C)
        B
        SFI system DTC is output (except DTC B2799, B279A and B279C)
        C



      B.
      GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

      C.
      GO TO SFI SYSTEM (Click here)
      A


      9.PROBLEM SYMPTOMS TABLE
      1. Refer to Problem Symptoms Table (Click here).

        Result:
        Result
        Proceed to
        Fault is not listed in Problem Symptoms Table
        A
        Fault is listed in Problem Symptoms Table
        B



      B.
      Go to step 11
      A


      10.OVERALL ANALYSIS AND TROUBLESHOOTING*
      1. Data List / Active Test (Click here)

      2. Terminals of ECU (Click here)


      NEXT


      11.REPAIR OR REPLACE

        NEXT


        12.CONFIRMATION TEST

          NEXT

          END