AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on .
Enter the following menus: "Powertrain / ECT / Data List".
According to the display on the tester, read "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Calculate Load | Calculated load by ECM: Min.: 0%, Max.: 100% |
| - |
| Engine Speed | Engine speed: Min.: 0 rpm, Max.: 16,383.75 rpm | 550 to 800 rpm: Idling | - |
| Vehicle Speed | Vehicle speed: Min.: 0 km/h, Max.: 255 km/h | Actual vehicle load | - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | 80 to 105°C (176 to 221°F): After warming up |
|
| Throttle Position | Throttle position: Min.: 0%, Max.: 100% | 10 to 22%: Idling | Calculated value based on VTA1 |
| Throttle Position from EFI | Throttle position: Min.: 0%, Max.: 100% |
| Recognition valve for throttle opening angle on ECM |
| SPD (NC) | Min.: 0 rpm, Max.: 12,750 rpm | - | - |
| SPD (NT) | Input turbine speed/ display: 50 r/min |
| - |
| Closed Throttle Position SW | Closed throttle position switch: ON or OFF |
| - |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever position is; P and N: ON Except P and N: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/ ON or OFF |
| - |
| Battery Voltage | Battery voltage: Min.: 0, Max.: 65.535 V | 9 to 14 V: Idling | - |
| TC and TE1 | TC and TE1 terminals of DLC3: ON or OFF | - | Active Test support data |
| Idle Fuel Cut | Fuel cut idle: ON or OFF | ON: Fuel cut operating | FC IDL="ON" when throttle valve fully closed and engine speed over 2,800 rpm |
| FC TAU | Fuel cut TAU (Fuel cut during very light load): | ON: Fuel cut operating | Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd, 4th, 5th or 6th | Shift lever position is;
| - |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF | Shift lever position is; R: ON Except R: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Shift SW Status (P Range) | PNP switch status/ ON or OFF | Shift lever position is; P: ON Except P: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Shift SW Status (N Range) | PNP switch status/ ON or OFF | Shift lever position is; N: ON Except N: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Shift SW Status (D Range) | PNP switch status/ ON or OFF | Shift lever position is; D and S: ON Except D and S: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF | Shift lever position is; S, "+" and "-": ON Except S, "+" and "-": OFF | - |
| TPS 1 Switch | 0: OFF / 1: ON | Gear position 1st, 2nd, 3rd or 4th: ON Gear position 5th or 6th: OFF | - |
| TPS 2 Switch | 0: OFF / 1: ON | Gear position 4th, 5th or 6th: ON Gear position 1st, 2nd or 3rd: OFF | - |
| TPS 3 Switch | 0: OFF / 1: ON | Shift solenoid valve SLU is ON: ON Shift solenoid valve SLU is OFF: OFF | - |
| A/T Oil Temperature 1 | ATF temp. sensor value/ min.: -40°C (-40°F) max.: 215°C (419°F) |
| If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor circuit is open or shorted. |
| NT Sensor Voltage | Min.: 0 V, Max.: 5 V | 0.1 to 1.9 V | - |
| NC Sensor Voltage | Min.: 0 V, Max.: 5 V | 0.1 to 1.9 V | - |
| AT Fluid | 0: OFF / 1: ON | - | - |
| Lock UP | 0: OFF / 1: ON | Lock up: ON | - |
| Lock UP Solenoid Status | Lock up solenoid status/ ON or OFF |
| - |
| SLU Solenoid Status | Shift Solenoid SLU Status/ ON or OFF |
| - |
| SLT Solenoid Status | Shift Solenoid SLT Status/ ON or OFF |
| - |
| Intake-Air Temp from EFI | Intake air temperature Min.: -40°C (-40°F), Max.: 215°C (419°F) | Equivalent to ambient air temperature |
|
| Accel Position from EFI | Min.: 0%, Max.: 100% |
| - |
| #Codes*1 | # of codes: Min.: 0, Max.: 255 | - | Number of detected DTCs |
| Check Mode*1 | Check mode: 0: OFF, 1: ON | ON: Check mode ON | - |
| SPD Test*1 | Check mode result for vehicle speed sensor: 0: COMPL, 1: INCMPL | - | - |
| MIL*1 | MIL status: ON or OFF | ON: MIL ON | - |
| On Run Distance*1 | MIL ON run distance: Min.: 0 km (0 mile), Max.: 110,950 mile (178,552 km) | Distance after DTC detected | - |
| Running Time from MIL ON*1 | Running time from MIL ON: Min.: 0 minute, Max.:65,535 minutes | Equivalent to running time after MIL ON | - |
| Engine Run Time | Engine run time: Min.: 0 second, Max.: 65,535 seconds | Time after engine start | - |
| Time after DTC Cleared | Time after DTC cleared: Min.: 0 minute, Max.: 65,535 minutes | Equivalent to time after DTCs erased | - |
| Distance from DTC Cleared | Distance after DTC cleared: Min.: 0 km/h, Max.: 65,535 km/h | Equivalent to time after DTCs erased | - |
| Warmup Cycle Cleared | Warm-up cycle after DTC cleared: Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| OBD Requirements*1 | OBD requirement | OBD2 | - |
| Complate Parts Monitor*1 | Comprehensive component monitor 0: NOT AVL / 1: AVAIL | - | Comprehensive component monitor |
| Transmission Type*1 | Transmission type | - | Identifying transmission type: 6 speed |
| SYSTEM | System identification | - | Identifying engine type: GASOLINE (gasoline engine) |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / Active Test".
According to the display on tester, perform "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate the shift solenoid valve and set each shift position by yourself. [Vehicle Condition] IDL: ON | [Shift Position] 0001: 1st / 0010: 2nd / 0011: 3rd / 0100: 4th / 0101: 5th / 0110: 6th | Possible to check the operation of the shift solenoid valves. Upshifts and downshifts should be performed consecutively. A 10-seconds interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. |
| Activate the Lock Up | [Test Details] Control the shift solenoid SLU to set the automatic transaxle to the lock-up condition. [Vehicle Condition]
| [Lock-up] 0: OFF / 1: ON | Possible to check the SLU solenoid operation. |
| Activate the Solenoid (SL1) | [Test Details] Operate the shift solenoid SL1 [Vehicle Condition]
| [Solenoid (SL1)] 0: OFF / 1: ON | - |
| Activate the Solenoid (SL2) | [Test Details] Operate the shift solenoid SL2 [Vehicle Condition]
| [Solenoid (SL2)] 0: OFF / 1: ON | - |
| Activate the Solenoid (SL3) | [Test Details] Operate the shift solenoid SL3 [Vehicle Condition]
| [Solenoid (SL3)] 0: OFF / 1: ON | - |
| Activate the Solenoid (SL4) | [Test Details] Operate the shift solenoid SL4 [Vehicle Condition]
| [Solenoid (SL4)] 0: OFF / 1: ON | - |
| Activate the Solenoid (SL) | [Test Details] Operate the shift solenoid SL [Vehicle Condition]
| [Solenoid (SL)] 0: OFF / 1: ON | - |
| Activate the Solenoid (SLT) | [Test Details] Operate the shift solenoid SLT and raise the line pressure. [Vehicle Condition]
| [Solenoid (SLT)] 0: OFF / 1: ON | - |
| Activate the Solenoid (SLU) | [Test Details] Operate the shift solenoid SLU and raise the line pressure. [Vehicle Condition]
| [Solenoid (SLU)] 0: OFF / 1: ON | - |