DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | Oxygen storage capacity value smaller than standard value under active air fuel ratio control (2 trip detection logic) |
|

| *1 | Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) | *2 | Air Fuel Ratio Sensor (Sensor 1) |
| *3 | Heated Oxygen Sensor (Sensor 2) | *4 | Front Exhaust Pipe Assembly (TWC: Rear Catalyst) |
| *5 | Center Exhaust Pipe Assembly | *6 | Tail Exhaust Pipe Assembly |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| UNKNOWN |
|


| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | +25% | Rich | Less than 3.1 V |
| -12.5% | Lean | More than 3.4 V | |
| O2S B1S2 (Heated oxygen) | +25% | Rich | More than 0.55 V |
| -12.5% | Lean | Less than 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Turn the tester on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor AFS Voltage B1S1 and O2S B1S2.
Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (air fuel ratio) | +25% | Rich | Less than 3.1 V |
| -12.5% | Lean | More than 3.4 V | |
| O2S B1S2 (heated oxygen) | +25% | Rich | More than 0.55 V |
| -12.5% | Lean | Less than 0.4 V |
| Status AFS Voltage B1S1 | Status O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensors Condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - |
| B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - |
| |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.INSPECT FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) |
Replace the exhaust manifold converter sub-assembly.
| NEXT | ||
| ||
| 5.INSPECT FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | ||
| ||
| 6.INSPECT FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | ||
| ||