DTC C1249/49 Open in Stop Light Switch Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1249/49 | When IG1 terminal voltage is 9.5 to 18.5 V, an open circuit of the stop light switch continues for 3 seconds or more. |
|

| 1.INSPECT STOP FUSE |
![]() |
Remove the STOP fuse from the main body ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| STOP (10 A) fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK STOP LIGHT OPERATION |
Install the STOP fuse.
Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed | ON |
| Brake pedal released | OFF |
|
| ||||
| OK | |
| 3.INSPECT SKID CONTROL ECU (STP TERMINAL) |
![]() |
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A26-27 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 8 to 14 V |
| A26-27 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
|
| ||||
| OK | |
| 4.INSPECT SKID CONTROL ECU (IG1 TERMINAL) |
![]() |
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A26-46 (IG1) - Body ground | Ignition switch on (IG) | 10 to 14 V |
|
| ||||
| OK | |
| 5.INSPECT SKID CONTROL ECU (GND TERMINAL) |
![]() |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A26-32 (GND1) - Body ground | Always | Below 1 Ω |
| A26-1 (GND2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.RECONFIRM DTC |
Reconnect the skid control ECU connector.
Clear the DTC (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
| Condition | Proceed to |
| DTC (C1249/49) is not output | A |
| DTC (C1249/49) is output | B |
|
| ||||
| A | ||
| ||
| 7.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL) |
![]() |
Disconnect the stop light switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A19-2 - Body ground | Always | 10 to 14 V |
|
| ||||
| OK | |
| 8.INSPECT STOP LIGHT SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Switch pin free | Below 1 Ω |
| 1 - 2 | Switch pin pushed in | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH) |
![]() |
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A26-27 (STP) - A19-1 | Always | Below 1 Ω |
| A26-27 (STP) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.RECONFIRM DTC |
Reconnect the skid control ECU connector and the stop light switch connector.
Clear the DTC (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
| Condition | Proceed to |
| DTC (C1249/49) is not output | A |
| DTC (C1249/49) is output | B |
|
| ||||
| A | ||
| ||