Vehicle Stability Control System:
Symptom
| Suspected Area
| See page
|
ABS, BA and/or EBD does not operate
| 1. Check the DTC again and make sure that the normal system code is output.
|
Click here
|
2. IG power source circuit
|
Click here
|
3. Front speed sensor circuit
|
Click here
|
4. Rear speed sensor circuit
|
Click here
|
5. Check the brake actuator assembly with the intelligent tester. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage.
|
Click here
|
6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU).
|
Click here
|
ABS, BA and/or EBD does not operate efficiently
| 1. Check the DTC again and make sure that the normal system code is output.
|
Click here
|
2. Front speed sensor circuit
|
Click here
|
3. Rear speed sensor circuit
|
Click here
|
4. Stop light switch circuit
|
Click here
|
5. Check the brake actuator assembly with the intelligent tester. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage.
|
Click here
|
6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU).
|
Click here
|
ABS sensor DTC check cannot be done
| 1. Check the DTC again and make sure that the normal system code is output.
|
Click here
|
2. TC and CG terminal circuit
|
Click here
|
3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU).
|
Click here
|
ABS warning light abnormal (Remains on)
| 1. ABS warning light circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|
ABS warning light abnormal (Does not come on)
| 1. ABS warning light circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|
BRAKE warning light abnormal (Remains on)
| 1. BRAKE warning light circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|
BRAKE warning light abnormal (Does not come on)
| 1. BRAKE warning light circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|
VSC and/or TRC does not operate
| 1. Check the DTC again and make sure that the normal system code is output.
|
Click here
|
2. IG power source circuit
|
Click here
|
3. Check the hydraulic circuit for leakage
| -
|
4. Front speed sensor circuit
|
Click here
|
5. Rear speed sensor circuit
|
Click here
|
6. Yaw rate and acceleration sensor circuit
|
Click here
|
7. Steering angle sensor circuit
|
Click here
|
8. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU).
|
Click here
|
VSC sensor DTC check cannot be done
| 1. Check the DTC again and make sure that the normal system code is output.
|
Click here
|
2. TC and CG terminal circuit
|
Click here
|
3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU).
|
Click here
|
SLIP indicator light abnormal (Remains on)
| 1. SLIP indicator light circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|
SLIP indicator light abnormal (Does not come on)
| 1. SLIP indicator light circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|
Sensor check cannot be done
| 1. TS and CG terminal circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|
Skid control buzzer abnormal
| 1. Skid control buzzer circuit
|
Click here
|
2. Brake actuator assembly (Skid control ECU)
|
Click here
|