Home › BODY ELECTRICAL › DOOR LOCK › ENTRY AND START SYSTEM

ENTRY AND START SYSTEM > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
  1. Use the following procedure to troubleshoot the entry and start system.
  2. *: Using the intelligent tester.



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS

      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      3. The following 5 items are important points in the problem analysis:

      What
      Vehicle model, system name
      When
      Date, time, occurrence frequency
      Where
      Road conditions
      Under what conditions?
      Running conditions, driving conditions, weather conditions
      How did it happen?
      Problem symptoms


    NEXT


    3.INSPECT BATTERY VOLTAGE
    1. Measure the battery voltage.

      Standard Voltage:
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


    NEXT


    4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM (CAN)*
    1. Use the intelligent tester to check if the CAN communication system (CAN) is functioning normally.

      Result:
      Result
      Proceed to
      ECU connected, communication line is normal.
      A
      ECU connected, communication line is malfunctioning (for LHD).
      B
      ECU connected, communication line is malfunctioning (for RHD).
      C



    B.
    GO TO CAN COMMUNICATION SYSTEM (for LHD) (Click here)

    C.
    GO TO CAN COMMUNICATION SYSTEM (for RHD) (Click here)
    A


    5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM (LIN)*
    1. Use the intelligent tester to check if the LIN communication system (LIN) is functioning normally (Click here).

      Result:
      Result
      Proceed to
      LIN DTC is not output.
      A
      LIN DTC is output.
      B



    B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
    A


    6.CHECK FOR DTC*
    1. Check for DTCs and note any codes that are output.

    2. Clear the DTCs.

    3. Recheck for DTCs. Based on the DTCs output, try to cause the same steering lock system DTC, engine immobiliser system DTC, wireless door lock control system DTC or entry and start system (start function) DTC to be output by simulating the symptoms indicated by the DTCs.

      Result:

      Result
      Proceed to
      DTC is not output.
      A
      Steering lock system DTC is output.
      B
      Engine immobiliser system DTC is output.
      C
      Wireless door lock control system DTC is output.
      D
      Entry and start system (start function) DTC is output.
      E



    B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    C.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    D.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    E.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
    A


    7.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).

      Result:
      Result
      Proceed to
      Fault is not listed in Problem Symptoms Table.
      A
      Fault is listed in Problem Symptoms Table.
      B



    B.
    Go to step 9
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING*
    1. Operation Check (Click here)

    2. Data List / Active Test (Click here)

    3. Terminals of ECU (Click here)


    NEXT


    9.REPAIR OR REPLACEMENT

      NEXT


      10.CONFIRMATION TEST

        NEXT

        END