Home › BODY ELECTRICAL › DOOR LOCK › ENTRY AND START SYSTEM

ENTRY AND START SYSTEM > Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here


DESCRIPTION

When the front passenger door entry lock and unlock functions do not operate, any of the following may be malfunctioning: 1) power door lock control system; 2) door electrical key oscillator (for front passenger side); or 3) certification ECU (smart key ECU assembly).

WIRING DIAGRAM


B164403E29


INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.
  2. Check that there are no electrical key transmitters in the vehicle.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (DOOR OUTSIDE HANDLE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start (Certification ECU (Smart Key ECU Assembly)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Touch Sensor
    Front passenger side door touch sensor / ON or OFF
    ON: Touch sensor is touched
    OFF: Touch sensor is not touched
    -
    P Trigger SW
    Front passenger side door lock switch / ON or OFF
    ON: Entry lock switch is pressed
    OFF: Entry lock switch is not pressed
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF according to the chart above.



NG
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side) (Click here)
OK


3.CHECK WAVE ENVIRONMENT


    B219251E01
  1. Bring the electrical key transmitter near the front door outside handle assembly (for front passenger side), and perform a front passenger door entry lock and unlock operation check.

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.

    HINT:
    1. When pressing the lock switch, hold the electrical key transmitter about 1 m (3.28 ft.) above the ground and about 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.
    2. When the electrical key transmitter is brought near the front door outside handle assembly (for front passenger side), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    3. If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry functions operate normally.



NG
Go to step 4
OK

AFFECTED BY WAVE INTERFERENCE 

4.PERFORM KEY DIAGNOSTIC MODE INSPECTION


    B219251E02
  1. Diagnostic mode inspection (door electrical key oscillator (for front passenger side))

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Utility / Key Communication Check / Overhead + Passenger Side.

    5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

      HINT:
      1. If the buzzer sounds, it can be determined that the door electrical key oscillator (for front passenger side) is operating normally.
      2. Hold the electrical key transmitter at the same height as the door outside handle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the key is as shown in the illustration.

      OK:
      Wireless door lock buzzer sounds.



NG
Go to step 5
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)
  1. Disconnect the certification ECU (smart key ECU assembly) connector.



    B171407E28
  1. Disconnect the door electrical key oscillator (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E74-6 (SEL2) - W2-4 (SEL)
    Always
    Below 1 Ω
    E74-36 (CG2B) - W2-5 (CLGB)
    Always
    Below 1 Ω
    E74-6 (SEL2) - Body ground
    Always
    10 kΩ or higher
    E74-36 (CG2B) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E74-6 (SEL2) - X2-4 (SEL)
    Always
    Below 1 Ω
    E74-36 (CG2B) - X2-5 (CLGB)
    Always
    Below 1 Ω
    E74-6 (SEL2) - Body ground
    Always
    10 kΩ or higher
    E74-36 (CG2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)


    B203441E39
  1. Disconnect the front door outside handle assembly (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    W1-2 (ANT2) - W2-8 (ANT2)
    Always
    Below 1 Ω
    W1-5 (ANT1) - W2-3 (ANT1)
    Always
    Below 1 Ω
    W1-2 (ANT2) - Body ground
    Always
    10 kΩ or higher
    W1-5 (ANT1) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    X1-2 (ANT2) - X2-8 (ANT2)
    Always
    Below 1 Ω
    X1-5 (ANT1) - X2-3 (ANT1)
    Always
    Below 1 Ω
    X1-2 (ANT2) - Body ground
    Always
    10 kΩ or higher
    X1-5 (ANT1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FUSE (DOME)
  1. Remove the DOME fuse from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DOME fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (DOME)
OK


8.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)


    B164336E48
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    W2-1 (+B) - W2-7 (GND)
    Always
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    X2-1 (+B) - X2-7 (GND)
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE DOOR ELECTRICAL KEY OSCILLATOR (for Front Passenger Side)
  1. Replace the door electrical key oscillator (for front passenger side) (Click here).


NEXT


10.CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Front Passenger Side)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (DOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)