Home › BODY ELECTRICAL › DOOR LOCK › ENTRY AND START SYSTEM

ENTRY AND START SYSTEM > Key Luggage Compartment Lock-in Prevention Function does not Operate

for Preparation Click here


DESCRIPTION

If the entry luggage compartment lock-in prevention function does not operate, either of the following may be the cause: 1) communication between the indoor electrical key oscillator (for luggage compartment) and electrical key antenna* cannot be performed; or 2) a malfunction in the certification ECU (smart key ECU assembly).
*: w/ Electrical Key Antenna

WIRING DIAGRAM


B164406E19


INSPECTION PROCEDURE

NOTICE:
The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.

1.CHECK ENTRY AND START SYSTEM (ENTRY LUGGAGE COMPARTMENT OPEN FUNCTION)
  1. Check that the entry luggage compartment open function operates.

    Result:
    Result
    Proceed to
    Entry luggage compartment door open function operates
    A
    Entry luggage compartment door open function does not operate
    B



B
GO TO OTHER PROBLEM (Click here)
A


2.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter near the indoor electrical key oscillator (for luggage compartment), and check that the entry luggage compartment lock-in prevention function operates.

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the indoor electrical key oscillator (for luggage compartment), communication is not possible.

    HINT:
    1. When the electrical key transmitter is brought near the indoor electrical key oscillator (for luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    Result:
    Result
    Proceed to
    Operation check fails
    A
    Operation check is normal
    B



B
AFFECTED BY WAVE INTERFERENCE
A


3.PERFORM KEY DIAGNOSTIC MODE INSPECTION


    B219249E01
  1. Diagnostic mode inspection (indoor electrical key oscillator (for luggage compartment))

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Utility / Key Communication Check / Overhead + Luggage (inside)

    5. When the electrical key transmitter is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

      HINT:
      1. Place the key on the luggage area.
      2. If the buzzer sounds, it can be determined that the indoor electrical key oscillators are operating normally.

      OK:
      Wireless door lock buzzer sounds



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INDOOR ELECTRICAL KEY OSCILLATOR)
  1. Disconnect the certification ECU (smart key ECU assembly) connector.



    B178763E23
  1. Disconnect the indoor electrical key oscillator (for luggage compartment) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-16 (CG7B) - N32-3 (CLGB)
    Always
    Below 1 Ω
    E74-15 (CLG7) - N32-1 (CLG6)
    Always
    Below 1 Ω
    E74-16 (CG7B) - Body ground
    Always
    10 kΩ or higher
    E74-15 (CLG7) - Body ground
    Always
    10 kΩ or higher

    Result:
    Result
    Proceed to
    OK (w/ Electrical Key Antenna)
    A
    OK (w/o Electrical Key Antenna)
    B
    NG
    C



B
Go to step 7

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)


    B193396E06
  1. Disconnect the door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-37 (ASEL) - O27-4 (ASEL)
    Always
    Below 1 Ω
    E74-37 (ASEL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - ELECTRICAL KEY ANTENNA)


    B164335E06
  1. Disconnect the electrical key antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O27-7 (ANT) - O29-1 (ANT)
    Always
    Below 1 Ω
    O27-7 (ANT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (for Luggage Compartment)
  1. Replace the indoor electrical key oscillator (for luggage compartment) (Click here).


NEXT


8.CHECK INDOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry function operates normally.

    Result:
    Result
    Proceed to
    NG (w/ Electrical Key Antenna)
    A
    NG (w/o Electrical Key Antenna)
    B
    OK
    C



B
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C
END (INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)
A


9.REPLACE ELECTRICAL KEY ANTENNA
  1. Replace the electrical key antenna (Click here).


NEXT


10.CHECK ELECTRICAL KEY ANTENNA (OPERATION)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry function operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (ELECTRICAL KEY ANTENNA WAS DEFECTIVE)