Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

TOYOTA PARKING ASSIST-SENSOR SYSTEM > Reverse Signal Circuit

for Preparation Click here


DESCRIPTION

The clearance warning ECU receives the reverse signal from the park/neutral position switch (for A/T) or back-up light switch (for M/T).

WIRING DIAGRAM


E159943E01


INSPECTION PROCEDURE

1.INSPECT FUSE (GAUGE NO. 1)
  1. Remove the GAUGE NO. 1 fuse from the main body ECU (instrument panel junction block ).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    GAUGE NO. 1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK CLEARANCE WARNING ECU (REVERSE SIGNAL INPUT)


    E159918E02
  1. Disconnect the S17 connector from the clearance warning ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S17-5 (BL) - Body ground
    Ignition switch ON, shift lever in R
    7 V or higher



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    for A/T (U250E)
    A
    for A/T (U660E)
    B
    for M/T
    C



B
Go to step 6

C
Go to step 8
A


4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - PARK/NEUTRAL POSITION SWITCH)


    E159916E02
  1. Disconnect the S17 connector from the clearance warning ECU.

  1. Disconnect the C1 connector from the park/neutral position switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-5 (BL) - C1-1 (RL)
    Always
    Below 1 Ω
    S17-5 (BL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT PARK/NEUTRAL POSITION SWITCH
  1. Remove the park/neutral position switch (Click here).



    E149961E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (RL) - 2 (RB)
    Shift lever in R
    Below 1 Ω
    1 (RL) - 2 (RB)
    Shift lever in any position except R
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

6.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - PARK/NEUTRAL POSITION SWITCH)


    E159916E03
  1. Disconnect the S17 connector from the clearance warning ECU.

  1. Disconnect the C1 connector from the park/neutral position switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-5 (BL) - C1-2 (RL)
    Always
    Below 1 Ω
    S17-5 (BL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT PARK/NEUTRAL POSITION SWITCH
  1. Remove the park/neutral position switch (Click here).



    E149961E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (RL) - 1 (RB)
    Shift lever in R
    Below 1 Ω
    2 (RL) - 1 (RB)
    Shift lever in any position except R
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

8.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - BACK-UP LIGHT SWITCH)


    E159920E01
  1. Disconnect the S17 connector from the clearance warning ECU.

  1. Disconnect the C28 connector from the back-up light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S17-5 (BL) - C28-1
    Always
    Below 1 Ω
    S17-5 (BL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT BACK-UP LIGHT SWITCH
  1. Remove the back-up light switch.



    E159912E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Push
    Below 1 Ω
    1 - 2
    Release
    10 kΩ or higher



NG
REPLACE BACK-UP LIGHT SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR