Home › TRANSMISSION ยท U660E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY

AUTOMATIC TRANSAXLE ASSEMBLY > REMOVAL

for Preparation Click here


NOTICE:
  1. When the automatic transaxle is replaced, the transaxle's compensation code must be input into the TCM (Click here).
  2. When the TCM is replaced, the existing transaxle compensation codes must be input into the new TCM (Click here).
  3. If the following parts have been replaced, initialize the TCM and perform a road test to allow the TCM to learn (Click here).
    1. Valve body assembly
    1. Shift solenoid SL3
    1. Shift solenoid SL4
  4. If the following parts have been replaced, perform a road test to allow the TCM to learn .
    1. Shift solenoid SL1
    1. Shift solenoid SL2
  5. If the TCM or transaxle has been replaced, register the transmission compensation code in the TCM (Click here).
  6. Perform the RESET MEMORY (AT initialization) when replacing the automatic transmission assembly, engine assembly or ECM (Click here).



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
(Click here)



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


4. REMOVE FRONT WHEELS


5. REMOVE ENGINE UNDER COVER LH


6. REMOVE ENGINE UNDER COVER RH


7. REMOVE FRONT FENDER APRON SEAL RH


8. DRAIN ENGINE OIL


9. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.



  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.


    A128117E02

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



10. DRAIN AUTOMATIC TRANSAXLE FLUID


    C142572
  1. Remove the refill plug and gasket.



    C142571
  1. Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket.



    C142574
  1. Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube.

  1. Drain the automatic transaxle fluid.



    C142574
  1. Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



    C142571
  1. Using a 6 mm socket hexagon wrench, install the overflow plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    C142572
  1. Install the refill plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



11. REMOVE WINDSHIELD WIPER LINK ASSEMBLY

HINT:
(Click here)



12. REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY


    A136272
  1. Remove the 4 bolts, 4 nuts and cowl top panel outer sub-assembly.



13. REMOVE COOL AIR INTAKE DUCT SEAL


    A132967
  1. Remove the 7 clips and intake duct seal.



14. REMOVE V-BANK COVER SUB-ASSEMBLY


    A132968
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.



15. REMOVE V-RIBBED BELT


    A129622E01
  1. Using SST, release the belt tension by turning the belt tensioner counterclockwise, and remove the V-ribbed belt from the belt tensioner.

    SST
    09249-63010  



    A095070
  1. While turning the belt tensioner counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner.



16. REMOVE AIR CLEANER INLET ASSEMBLY


    A132969
  1. Remove the 2 bolts, clamp and air cleaner inlet.



17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A135704
  1. Disconnect the 3 vacuum hoses.



    A135705E01
  1. Disconnect the mass air flow meter connector (*1).

  1. Disconnect the No. 2 ventilation hose (*2).

  1. Disconnect the hose band (*3).



    A135706
  1. Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.



18. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A132971
  1. Disconnect the vacuum hose and hose clamp.

  1. Remove the 3 bolts and air cleaner case.



19. REMOVE NO. 1 AIR CLEANER INLET


    A132970
  1. Remove the bolt and No. 1 air cleaner inlet.



20. REMOVE BATTERY


    A132972
  1. Loosen the bolt and nut, and remove the battery clamp.

  1. Remove the battery and battery tray.



21. REMOVE INTAKE AIR RESONATOR SUB-ASSEMBLY


    A133928
  1. Remove the clip, bolt and intake air resonator.



22. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A132985
  1. Remove the bolt, 2 nuts, and No. 2 mounting stay RH.



23. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY


    A132986
  1. Remove the 4 bolts and engine moving control rod.



24. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE


    A132983
  1. Remove the clamp and disconnect the No. 1 fuel vapor feed hose.



25. DISCONNECT CHECK VALVE TO BRAKE BOOSTER HOSE


    A132982
  1. Remove the clamp and disconnect the check valve to brake booster hose.



26. REMOVE RADIATOR HOSE INLET


    A132979
  1. Remove the clamp and disconnect the radiator hose inlet.



27. REMOVE RADIATOR HOSE OUTLET


    A132980
  1. Remove the clamp and disconnect the radiator hose outlet.



28. DISCONNECT NO. 1 OIL COOLER INLET HOSE


    A133003
  1. Remove the clamp and disconnect the oil cooler inlet hose.



29. DISCONNECT NO. 1 OIL COOLER OUTLET HOSE
  1. Remove the clamp and disconnect the oil cooler outlet hose.



30. DISCONNECT HEATER WATER HOSE INLET


    A132978
  1. Disconnect the heater inlet water hose.



31. DISCONNECT HEATER WATER HOSE OUTLET
  1. Disconnect the heater outlet water hose.



32. REMOVE ECM


    A135711
  1. Remove the 3 nuts.



    A128952E01
  1. Disconnect the 2 connectors and remove the ECM.



    A135713
  1. Remove the 4 screws and 2 ECM brackets.



33. REMOVE RELAY BLOCK COVER UPPER


34. DISCONNECT ENGINE WIRE


    A132975
  1. Disconnect the engine wire from the engine room junction block.

    1. Remove the nut and separate the wire harness.

    2. Using a screwdriver, unlock the engine room J/B. Pull the engine room J/B upward.

    3. Disconnect the engine wire connectors.



    A132976
  1. Remove the 2 bolts and 2 clamps from the body.



    A132981
  1. Remove the bolt and clamp from the bracket.



35. SEPARATE WIRE HARNESS


    C096795
  1. Remove the bolt and disconnect the wire harness.



36. DISCONNECT CONNECTOR


    C132238
  1. Disconnect the park/neutral position switch connector.



37. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    A132973
  1. Remove the clip and nut, and separate the cable from the transaxle.



38. SEPARATE FUEL TUBE SUB-ASSEMBLY


    A129626
  1. Remove the No. 1 fuel pipe clamp.



    B012941E15
  1. Disconnect the connector from the tube while pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for contamination in the pipe and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.



39. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE


    A129629
  1. Disconnect the No. 1 oil reservoir to pump hose.



40. DISCONNECT RETURN TUBE SUB-ASSEMBLY


    A132984
  1. Disconnect the return tube sub-assembly.



41. REMOVE EXHAUST PIPE NO. 1 SUPPORT BRACKET


    A085549E01
  1. Remove the 2 nuts and front support brackets.



42. REMOVE EXHAUST PIPE ASSEMBLY FRONT
  1. Disconnect the 2 heated oxygen sensor (bank 1, 2 sensor 2) connectors.



  1. Remove the 2 nuts from the exhaust front pipe (left bank exhaust manifold side).


    A135720

  1. Remove the 2 nuts from the exhaust front pipe (right bank exhaust pipe manifold side).

  1. Remove the exhaust front pipe.

  1. Remove the 2 gaskets from the exhaust front pipe.



43. REMOVE FRONT AXLE HUB NUT LH


    C108168E02
  1. Using SST and a hammer, release the staked part of the front axle hub nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.



44. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures described for the LH side.



45. DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH


    C140591
  1. Remove the nut and separate the front stabilizer link assembly.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



46. DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



47. DISCONNECT FRONT SPEED SENSOR LH


    C140592
  1. Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.



    C132782E01
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.



48. DISCONNECT FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.



49. DISCONNECT TIE ROD ASSEMBLY LH


    C108515E02
  1. Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end sub-assembly from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Make sure that the string of the SST is securely tied to the vehicle.
    2. Be careful not to damage the ball joint dust cover.
    3. Be careful not to damage the steering knuckle.
    4. Be careful not to damage the front disc brake dust cover.



50. DISCONNECT TIE ROD ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



51. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM LH


    F040142E01
  1. Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.



52. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures described for the LH side.



53. SEPARATE FRONT AXLE ASSEMBLY LH


    D032030E06
  1. Put matchmarks on the front drive shaft assembly and the axle hub.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.



54. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



55. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET
  1. Remove the No. 1 exhaust pipe support bracket with the 2 bolts.



56. REMOVE FLYWHEEL HOUSING UNDER COVER


    C135005
  1. Remove the 2 bolts, exhaust pipe support bracket and flywheel housing under cover.



57. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    D002828
  1. Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.



58. DISCONNECT STEERING SLIDING YOKE


    C133501
  1. Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.



    C132548E02
  1. Remove the bolt and slide the steering sliding yoke.

    NOTICE:
    Do not separate the steering sliding yoke from the power steering link assembly.



    C132549E01
  1. Put matchmarks on the steering sliding yoke and the power steering link assembly.

  1. Separate the steering sliding yoke from the power steering link assembly.



59. REMOVE GENERATOR ASSEMBLY


    A133865
  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. Disconnect the connector from the compressor and magnetic clutch.

  1. Disconnect the 2 wire harness clamps.



    A133866
  1. Remove the 2 bolts.



    A133867
  1. Remove the bolt from the cylinder block.

  1. Disconnect the wire harness clamp and remove the generator assembly.



    A128066
  1. Remove the bolt and wire harness clamp stay.



    A135391
  1. Remove the bolt and bracket.



60. SEPARATE COOLER COMPRESSOR ASSEMBLY


    A132977
  1. Remove the 2 connector clamps.

  1. Remove the 4 bolts and separate the compressor.

    HINT:
    Hang up the hoses instead of detaching them.



61. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine lifter.



    A129634
  1. Remove the 4 bolts, 2 nuts, and frame side rail plates RH and LH.

  1. Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.

  1. Operate the engine lifter, then remove the engine assembly from the vehicle.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.



62. REMOVE VANE PUMP ASSEMBLY
  1. Disconnect the power steering oil pressure switch connector.



    A138331E01
  1. Remove the pressure feed tube clamp bolt.

  1. Loosen the bolt A.

  1. Remove the bolt B and vane pump.



63. INSTALL ENGINE HANGERS


    A129635E03
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 Engine hanger 12281-31120
    No. 2 Engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.



64. REMOVE FRONT FRAME ASSEMBLY


    A132990
  1. Disconnect the connector and clamp.



    A132989
  1. Disconnect the 2 clamps.



    A078403E05
  1. Remove the 2 nuts and disconnect the engine mounting insulators RH and LH.



    A132988
  1. Remove the bolt and disconnect the engine mounting insulator FR.



65. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C083850E02
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    2. Be careful not to drop the drive shaft assembly.



66. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C080304E03
  1. Using a screwdriver, remove the bearing bracket hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot and oil seal.



67. REMOVE ENGINE WIRE


68. REMOVE STARTER ASSEMBLY


    A133864
  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Remove the 2 bolts and starter assembly.



69. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY


    C142575E01
  1. Remove the bolt and breather bracket from the camshaft housing sub-assembly LH.

  1. Remove the breather hose from the breather bracket.



    C135007
  1. Remove the 11 bolts.

  1. Separate and remove the automatic transaxle.



70. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


    C139850E01
  1. Put matchmarks on the transaxle housing and torque converter clutch assembly.

  1. Remove the torque converter clutch assembly from the automatic transaxle assembly.



71. REMOVE ENGINE MOUNTING FRONT BRACKET


    C133601
  1. Remove the 3 bolts and engine mounting front bracket.



72. REMOVE TCM


    C139840E01
  1. Remove the 2 bolts and TCM from the transaxle.



73. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY


    C135002
  1. Remove the bolt and hole cover from the transaxle case.

  1. Remove the O-ring from the hole cover.



74. REMOVE WIRE HARNESS CLAMP BRACKET (for LHD)


    C139880
  1. Remove the 4 bolts and 4 clamp brackets.



75. REMOVE WIRE HARNESS CLAMP BRACKET (for RHD)


    C143321
  1. Remove the 5 bolts and 5 clamp brackets.



76. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    C139615
  1. Remove the 2 bolts and No. 1 transmission control cable bracket.



77. SEPARATE NO. 1 OIL COOLER OUTLET HOSE


    C139881
  1. Separate the No. 1 oil cooler outlet hose.



78. SEPARATE NO. 1 OIL COOLER INLET HOSE


    C139882
  1. Separate the No. 1 oil cooler inlet hose.