Home › TRANSMISSION ยท E351 MANUAL TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY

MANUAL TRANSAXLE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


4. REMOVE FRONT WHEELS


5. REMOVE ENGINE UNDER COVER LH


6. REMOVE ENGINE UNDER COVER RH


7. REMOVE FRONT FENDER APRON SEAL RH


8. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.



9. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.



  1. Loosen the radiator drain cock plug and cylinder block drain cock plug, then drain the coolant.


    A136224E04

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



10. DRAIN MANUAL TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



11. DRAIN BRAKE FLUID

NOTICE:
  1. Stop the engine and depress the brake pedal several times until no vacuum is left in the brake booster.
  2. If the brake fluid leaks onto any painted surface, wash off and remove the brake fluid completely.



12. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
Click here.


13. REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY


    A136272
  1. Remove the 4 bolts, 4 nuts and outer cowl top panel sub-assembly.



14. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A134904
  1. Remove the 2 nuts and cover.



15. REMOVE V-RIBBED BELT


    A114351E03
  1. Using SST and 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then remove the V-ribbed belt.

    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply force any more than necessary.



16. REMOVE AIR CLEANER INLET ASSEMBLY


    A134903
  1. Remove the 2 bolts, clamp and air cleaner inlet.



17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A135666E01
  1. Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).



    A135667E01
  1. Disconnect the No. 2 ventilation hose from the air cleaner hose.



    A135668
  1. Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.



    A135669
  1. Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.



18. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A135666E01
  1. Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).



    A135667E01
  1. Disconnect the No. 2 ventilation hose from the air cleaner hose.



    A135668
  1. Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.



    A135669
  1. Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.



19. REMOVE BATTERY


    A134906
  1. Loosen the bolt and nut, and remove the battery clamp.

  1. Remove the battery and battery tray.



20. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A134912
  1. Remove the 2 bolts and No. 2 mounting stay RH.



21. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY


    A134909
  1. Remove the bolt and disconnect the ground cable.



    A134910
  1. Remove the 3 bolts and the engine moving control rod with bracket.



22. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH


    A134911
  1. Remove the 3 bolts and No. 2 mounting bracket RH.



23. DISCONNECT NO. 1 VACUUM HOSE CONNECTOR


    A134908
  1. Remove the clamp and disconnect the vacuum hose connector.



24. DISCONNECT RADIATOR HOSE INLET


    A134907
  1. Remove the clamp and disconnect the radiator hose inlet.



25. DISCONNECT RADIATOR HOSE OUTLET


    A127545
  1. Remove the clamp and disconnect the radiator hose outlet.



26. DISCONNECT HEATER WATER HOSE INLET


    A124832
  1. Disconnect the heater inlet water hose.



27. DISCONNECT HEATER WATER HOSE OUTLET


    A124831
  1. Disconnect the heater outlet water hose.



28. REMOVE ECM
Click here.


29. DISCONNECT ENGINE WIRE


    A132975
  1. Disconnect the engine wire from the engine room relay block.

    1. Remove the nut and separate the wire harness.

    2. Using a screwdriver, unlock the engine room R/B. Pull the engine room R/B upward.

    3. Disconnect the engine wire connectors.



    A134913
  1. Remove the clamp from the bracket.



    A134914
  1. Remove the 2 bolts and clamp from the body.



30. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C132952
  1. Remove the 2 clips and 2 washers and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.



31. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE


    A060072
  1. Disconnect the No. 1 oil reservoir to pump hose.



32. DISCONNECT RETURN TUBE SUB-ASSEMBLY


    A060073
  1. Disconnect the return tube sub-assembly.



33. REMOVE CLUTCH ACCUMULATOR ASSEMBLY
Click here.


34. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY
Click here.


35. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A129626
  1. Remove the No. 1 fuel pipe clamp.



    B012941E15
  1. Disconnect the connector from the tube while pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for contamination in the pipe and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.



36. REMOVE GENERATOR ASSEMBLY


    A135170
  1. Disconnect the generator connector.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and wire harness clamp bracket.

  1. Remove the wire harness clamps.



    A133567
  1. Remove the 2 bolts and generator assembly.



37. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH


    A134944
  1. Disconnect the connector.

  1. Remove the 4 bolts and separate the compressor.

    HINT:
    Hang up the hoses instead of detaching them.



38. REMOVE FRONT EXHAUST PIPE ASSEMBLY
Click here.


39. REMOVE FRONT AXLE HUB NUT LH


    C108168E02
  1. Using SST and a hammer, release the staked part of the front axle hub nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.



40. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures described for the LH side.



41. REMOVE FRONT STABILIZER LINK ASSEMBLY LH


    C140591
  1. Remove the nut and separate the front stabilizer link assembly.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



42. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



43. REMOVE FRONT SPEED SENSOR LH


    C140592
  1. Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.



    C132782E01
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.



44. REMOVE FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.



45. DISCONNECT TIE ROD ASSEMBLY LH


    C108515E02
  1. Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end sub-assembly from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Make sure that the string of the SST is securely tied to the vehicle.
    2. Be careful not to damage the ball joint dust cover.
    3. Be careful not to damage the steering knuckle.
    4. Be careful not to damage the front disc brake dust cover.



46. DISCONNECT TIE ROD ASSEMBLY RH


47. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM LH


    F040142E01
  1. Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.



48. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures described for the LH side.



49. SEPARATE FRONT AXLE ASSEMBLY LH


    D032030E06
  1. Put matchmarks on the front drive shaft assembly and the axle hub.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.



50. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



51. SEPARATE STEERING SLIDING YOKE


    C133501
  1. Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.



    C132548E02
  1. Remove the bolt and slide the steering sliding yoke.

    NOTICE:
    Do not separate the steering sliding yoke from the power steering link assembly.



    C132549E01
  1. Put matchmarks on the steering sliding yoke and the power steering link assembly.

  1. Separate the steering sliding yoke from the power steering link assembly.



52. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


    A059877
  1. Set the engine lifter.

  1. Remove the 4 bolts, 2 nuts and frame side rail plate RH and LH.



    A059878
  1. Remove the 4 bolts, 2 nuts and front suspension member brace rear RH and LH.

  1. Carefully remove the engine assembly from the vehicle.



    A090847E03
  1. Install the 2 engine hangers as shown in the illustration.
    Parts No.:
    Parts
    Parts No.
    No. 1 Engine hanger
    12281-28010
    No. 2 Engine hanger
    12282-28010
    Bolt
    91512-61020

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Using a chain block and an engine sling device, hang the engine assembly.



53. REMOVE VANE PUMP ASSEMBLY


    A059879
  1. Disconnect the oil pressure switch connector.

  1. Loosen the 2 bolts and remove the vane pump from the engine.



54. REMOVE FRONT FRAME ASSEMBLY


    A052490E01
  1. A/T:
    Remove the nut from the engine mounting insulator LH.



    A059881E01
  1. M/T:
    Remove the bolt from the engine mounting insulator LH.



    A052482
  1. Remove the nut from the engine mounting insulator RH.



    A059880
  1. Remove the bolt from the engine mounting insulator FR.



    A060825E04
  1. M/T:
    Remove the bolt from the engine lateral control rod.

  1. Raise the engine assembly and separate the front frame.



55. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C083850E02
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    2. Be careful not to drop the drive shaft assembly.



56. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C080304E03
  1. Using a screwdriver, remove the bearing bracket hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot and oil seal.



57. REMOVE STARTER ASSEMBLY


    A133565
  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut and disconnect the wire harness from terminal 30.



    A133566E01
  1. Remove the 3 bolts, clutch flexible hose bracket and starter assembly.



58. DISCONNECT WIRE HARNESS
  1. Remove the bolt and separate the ground cable.

  1. Disconnect the back-up light switch connector.

  1. Disconnect the wire harness.



59. REMOVE MANUAL TRANSAXLE ASSEMBLY


    D025747
  1. Remove the 10 bolts.

  1. Separate and remove the transaxle from the engine.



60. REMOVE CLUTCH LINE


    C132979
  1. Remove the 2 bolts, clutch line and bracket.



61. REMOVE WIRE HARNESS CLAMP


    C132983
  1. Remove the 2 bolts and wire harness clamps.



62. REMOVE MANUAL TRANSMISSION CASE PROTECTOR


    C132980
  1. Remove the 2 bolts and manual transmission case protector.



63. REMOVE ENGINE MOUNTING FRONT BRACKET


    C132981
  1. Remove the 3 bolts and engine mounting front bracket.



64. REMOVE ENGINE MOUNTING INSULATOR LH


    C132982
  1. Remove the 4 bolts and engine mounting insulator LH.