DTC C0200/31 Right Front Wheel Speed Sensor Signal Malfunction |
DTC C0205/32 Left Front Wheel Speed Sensor Signal Malfunction |
DTC C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1330/35 Right Front Speed Sensor Circuit |
DTC C1331/36 Left Front Speed Sensor Circuit |

| DTC No. | DTC Detecting Condition | Trouble Area |
| C0200/31 C0205/32 | When either of the following is detected:
|
|
| C1330/35 C1331/36 | Abnormality in the resistance value of each speed sensor is detected. |
|
| C1271/71 C1272/72 | Detected only during test mode. |
|
| C1275/75 C1276/76 | Detected only during test mode. |
|

| 1.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select "Data List" and read the value displayed on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition |
| FR Wheel Speed | Wheel speed sensor (FR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
| FL Wheel Speed | Wheel speed sensor (FL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Check if test mode (signal check) DTCs are detected (Click here).
| Condition | Proceed to |
| Test mode (signal check) DTC is not output | A |
| Test mode (signal check) DTC is output | B |
|
| ||||
| A | |
| 3.INSPECT SPEED SENSOR SIGNAL WAVEFORM |
![]() |
Lift up the vehicle.
Perform the inspection using an oscilloscope.
Disconnect the front speed sensor connector.
Connect the oscilloscope to terminals 1 and 2 of the front speed sensor.
Check that a waveform is output when the tires are rotated.
Connect the connector.
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.
Check if the same DTCs are recorded (Click here).
| Condition | Proceed to |
| DTCs (C0200/31, C0205/32, C1330/35 and C1331/36) are output | A |
| DTCs (C0200/31, C0205/32, C1330/35 and C1331/36) are output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE) | B |
| DTCs (C0200/31, C0205/32, C1330/35 and C1331/36) are not output (When troubleshooting in accordance with the DTC CHART) | C |
|
| ||||
|
| ||||
| A | |
| 5.INSPECT FRONT SPEED SENSOR INSTALLATION |
![]() |
Check the front speed sensor installation.
|
| ||||
| OK | |
| 6.INSPECT FRONT SPEED SENSOR |
![]() |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the front speed sensor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| A14-1 (FL+) - A14-2 (FL-) | 1.4 to 1.8 kΩ at 20°C (68°F) |
| A14-1 (FL+) - Body ground | 10 kΩ or higher |
| A14-2 (FL-) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| A35-1 (FR+) - A35-2 (FR-) | 1.4 to 1.8 kΩ at 20°C(68°F) |
| A35-1 (FR+) - Body ground | 10 kΩ or higher |
| A35-2 (FR-) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR TO SKID CONTROL ECU) |
![]() |
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| A25-5 (FL+) - A14-1 (FL+) | Below 1 Ω |
| A25-6 (FL-) - A14-2 (FL-) | Below 1 Ω |
| A14-1 (FL+) - Body ground | 10 kΩ or higher |
| A14-2 (FL-) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| A25-10 (FR+) - A35-1 (FR+) | Below 1 Ω |
| A25-9 (FR-) - A35-2 (FR-) | Below 1 Ω |
| A35-1 (FR+) - Body ground | 10 kΩ or higher |
| A35-2 (FR-) - Body ground | 10 kΩ or higher |
Connect the connectors.
|
| ||||
| OK | |
| 8.INSPECT SPEED SENSOR SIGNAL WAVEFORM |
![]() |
Lift up the vehicle.
Perform the inspection using an oscilloscope.
Disconnect the front speed sensor connector.
Connect the oscilloscope to terminals 1 and 2 of the front speed sensor.
Check that a waveform is output when the tires are rotated.
Connect the connector.
|
| ||||
| OK | |
| 9.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select "Data List" and read the value displayed on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition |
| FR Wheel Speed | Wheel speed sensor (FR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
| FL Wheel Speed | Wheel speed sensor (FL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 10.RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.
Check if the same DTCs are recorded (Click here).
| Condition | Proceed to |
| DTCs (C0200/31, C0205/32, C1330/35 and C1331/36) are output | A |
| DTCs (C0200/31, C0205/32, C1330/35 and C1331/36) are not output | B |
|
| ||||
| A | |
| 11.INSPECT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the sensor tip.
Install the speed sensor.
|
| ||||
| OK | ||
| ||