ANTI-LOCK BRAKE SYSTEM > Brake Warning Light Remains ON |


| 1.CHECK DTC |
Check if an ABS DTC is output (Click here).
| Condition | Proceed to |
| CAN communication system DTC is not output | A |
| CAN communication system DTC is output | B |
|
| ||||
| A | |
| 2.INSPECT CAN COMMUNICATION SYSTEM |
Check if a CAN communication system DTC is output (Click here).
| Condition | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 3.CHECK IF SKID CONTROL ECU CONNECTOR SECURELY CONNECTED |
Check if the skid control ECU connector is connected securely.
|
| ||||
| OK | |
| 4.CHECK BATTERY |
Check the battery voltage.
|
| ||||
| OK | |
| 5.INSPECT SKID CONTROL ECU CONNECTOR (IG1 TERMINAL VOLTAGE) |
![]() |
Disconnect the skid control ECU connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-18 (IG1) - Body ground | Ignition switch on | 10 to 14 V |
|
| ||||
| OK | |
| 6.INSPECT SKID CONTROL ECU CONNECTOR (GND TERMINAL CONTINUITY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| A25-4 (GND1) - Body ground | Below 1 Ω |
| A25-1 (GND2) - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 7.INSPECT PARKING BRAKE SWITCH |
![]() |
Remove the parking brake switch.
Disconnect the parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| (A18-1) - Ground part | Free | Below 1 Ω |
| (A18-1) - Ground part | Pushed in | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| (E33-1) - Ground part | Free | Below 1 Ω |
| (E33-1) - Ground part | Pushed in | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU TO PARKING BRAKE SWITCH) |
![]() |
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| IC-14 - A18-1 (PKB) | Below 1 Ω |
| A18-1 (PKB) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| IM-2 (PKB) - E33-1 (PKB) | Below 1 Ω |
| E33-1 (PKB) - Body ground | 10 kΩ or higher |
Connect the connector.
|
| ||||
| OK | |
| 9.INSPECT BRAKE FLUID LEVEL WARNING SWITCH ASSEMBLY |
![]() |
Remove the reservoir tank cap.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| (A16-1) - (A16-2) | Float UP | 10 kΩ or higher (No Continuity) |
| (A16-1) - (A16-2) | Float DOWN | Below 1 Ω (Continuity) |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH TO COMBINATION METER) |
![]() |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| A16-1 - F2-6 (B/LE) | Below 1 Ω |
| F2-6 (B/LE) - Body ground | 10 kΩ or higher |
| A16-2 - Body ground | Below 1 Ω |
Connect the connector.
|
| ||||
| OK | |
| 11.INSPECT COMBINATION METER ASSEMBLY |
Connect the intelligent tester to the DLC3.
Select the "Active Test" on the tester (Click here).
| Tester Display | Test Part/Control Range | Diagnostic Note |
| Brake Warning Light | Turn brake warning light ON / OFF | Observe combination meter |
Check the ABS warning light operation.
| Condition | Proceed to |
| OK | A |
| OK (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||