Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

REAR VIEW MONITOR SYSTEM > Image from Camera for Rear View Monitor is Abnormal

for Preparation Click here


DESCRIPTION

The display signal from the rear television camera assembly transmits to the navigation receiver assembly.

WIRING DIAGRAM


w/o Entry and Start System

E183755E07


w/ Entry and Start System

E183754E03


INSPECTION PROCEDURE

1.CONFIRM MODEL
  1. Chose the model to be inspected.

    Result:
    Result
    Proceed to
    w/o Entry and Start System
    A
    w/ Entry and Start System
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - REAR TELEVISION CAMERA)


    E183802E01
  1. Disconnect the F24 connector from the navigation receiver assembly and the S19 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S19-6 (CV+) - F24-1 (V+)
    Always
    Below 1 Ω
    S19-5 (CB+) - F24-2 (CA+)
    Always
    Below 1 Ω
    S19-1 (CGND) - F24-12 (CGND)
    Always
    Below 1 Ω
    S19-2 (CV-) - F24-11 (V-)
    Always
    Below 1 Ω
    S19-6 (CV+) - Body ground
    Always
    10 kΩ or higher
    S19-5 (CB+) - Body ground
    Always
    10 kΩ or higher
    S19-1 (CGND) - Body ground
    Always
    10 kΩ or higher
    S19-2 (CV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER - REAR TELEVISION CAMERA)
OK


3.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Reconnect the S19 connector to the rear television camera assembly.



    E185299E03
  1. Reconnect the F24 connector to the navigation receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-11 (V-) - Body ground
    Always
    Below 1 Ω
    F24-12 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F24-2 (CA+) - F24-12 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7 V

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4.INSPECT REAR TELEVISION CAMERA ASSEMBLY


    E183803E01
  1. Check that the F27 and F24 connectors are connected to the navigation receiver assembly.



    E171712E02
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F24-1 (V+) - F27-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (to Navigation Receiver Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - LUGGAGE COMPARTMENT DOOR OPENER SWITCH)


    E183802E01
  1. Disconnect the F24 connector from the navigation receiver assembly and the S19 connector from the luggage compartment door opener outer switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S19-6 (CV+) - F24-1 (V+)
    Always
    Below 1 Ω
    S19-5 (CB+) - F24-2 (CA+)
    Always
    Below 1 Ω
    S19-1 (CGND) - F24-12 (CGND)
    Always
    Below 1 Ω
    S19-2 (CV-) - F24-11 (V-)
    Always
    Below 1 Ω
    S19-6 (CV+) - Body ground
    Always
    10 kΩ or higher
    S19-5 (CB+) - Body ground
    Always
    10 kΩ or higher
    S19-1 (CGND) - Body ground
    Always
    10 kΩ or higher
    S19-2 (CV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Luggage Compartment Door Opener Outer Switch)



NG
REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER - LUGGAGE COMPARTMENT DOOR OPENER SWITCH)
OK


6.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Reconnect the S19 connector to the luggage compartment door opener outer switch.



    E185299E03
  1. Reconnect the F24 connector to the navigation receiver assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-11 (V-) - Body ground
    Always
    Below 1 Ω
    F24-12 (CGND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F24-2 (CA+) - F24-12 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7 V

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


7.INSPECT REAR TELEVISION CAMERA ASSEMBLY


    E183803E01
  1. Check that the F27 and F24 connectors are connected to the navigation receiver assembly.



    E171712E02
  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    F24-1 (V+) - F27-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *1
    Component with harness connected
    (to Navigation Receiver Assembly)
    *2
    Waveform 1 (under normal conditions)
    *3
    Waveform 2 (camera lens is covered, blacking out the screen)
    *4
    Synchronized Signal
    *5
    Video Waveform



NG
Go to step 8
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

8.REPLACE LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH
  1. Replace the luggage compartment door opener outer switch with a new or normally functioning one (Click here).


NEXT


9.CONFIRM SYMPTOMS
  1. Check if the same malfunction recurs when the rear view monitor screen is displayed.

    Result:
    Result
    Proceed to
    Malfunction does not reoccur
    (returns to normal)
    A
    Malfunction reoccurs
    B



B
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
A

END