Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

DTC    B2312    Power Window Switch Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor assembly is operated by the power window regulator master switch assembly or power window regulator switch assembly. The power window regulator motor assembly has motor, regulator and ECU functions.
This DTC is output when the ECU built into the regulator motor determines that the power window regulator master switch assembly or power window regulator switch assembly is stuck.

HINT:
DTC B2312 can be stored in the power window regulator master switch assembly and in each power window regulator motor assembly (power window ECU).


Master Switch (Power Window Regulator Master Switch Assembly) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator master switch assembly stuck
  2. Power window regulator master switch assembly held in same position for more than 20 seconds
Power window regulator master switch assembly

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Side)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator master switch assembly (for driver side) stuck
  2. Power window regulator master switch assembly held in same position for more than 20 seconds
  1. Power window regulator master switch assembly
  2. Power window regulator motor assembly (for driver side)
  3. Wire harness or connector

P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Side)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator switch assembly (for front passenger side) stuck
  2. Power window regulator switch assembly held in same position for more than 20 seconds
  1. Power window regulator switch assembly (for front passenger side)
  2. Power window regulator motor assembly (for front passenger side)
  3. Wire harness or connector

RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Side)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator switch assembly (for rear LH side) stuck
  2. Power window regulator switch assembly held in same position for more than 20 seconds
  1. Power window regulator switch assembly (for rear LH side)
  2. Power window regulator motor assembly (for rear LH side)
  3. Wire harness or connector

RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Side)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator switch assembly (for rear RH side) stuck
  2. Power window regulator switch assembly held in same position for more than 20 seconds
  1. Power window regulator switch assembly (for rear RH side)
  2. Power window regulator motor assembly (for rear RH side)
  3. Wire harness or connector

WIRING DIAGRAM


for Driver Side

B203536E08


for Front Passenger Side

B203371E33


for Rear LH Side

B203371E30


for Rear RH Side

B203371E31


INSPECTION PROCEDURE

NOTICE:
  1. When the power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized.
  2. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
    1. Close the power window by fully pulling up the power window regulator master switch assembly or power window regulator switch assembly and holding it at the auto up position.
    2. Open the power window by fully pushing down the switch.

1.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE) 

2.CHECK DTC
  1. Check for DTC output conditions.

    Result:
    Result
    Proceed to
    DTC output from power window regulator master switch assembly
    A
    DTC output from power window regulator motor assembly (for driver side)
    B
    DTC output from power window regulator motor assembly (for front passenger side)
    C
    DTC output from power window regulator motor assembly (for rear LH side)
    D
    DTC output from power window regulator motor assembly (for rear RH side)
    E



B
Go to step 3

C
Go to step 5

D
Go to step 8

E
Go to step 11
A

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)  

3.READ VALUE USING INTELLIGENT TESTER (D-Door Motor)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / D-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    D-Door Motor (Power Window Regulator Motor Assembly (for Driver Side)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver side power window manual up switch signal / ON or OFF
    ON: Driver door power window manual up switch operated
    OFF: Driver door power window manual up switch not operated
    -
    D Door P/W Down SW
    Driver side power window manual down switch signal / ON or OFF
    ON: Driver door power window manual down switch operated
    OFF: Driver door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) (Click here)  

4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)
  1. Disconnect the power window regulator master switch assembly connector.



    B193520E07
  1. Disconnect the power window regulator motor assembly (for driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-20 (UP) - Body ground
    Always
    10 kΩ or higher
    M2-15 (DOWN) - Body ground
    Always
    10 kΩ or higher
    I5-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I5-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) (Click here)  

5.READ VALUE USING INTELLIGENT TESTER (P-Door Motor)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / P-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Side)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto up/down switch signal / ON or OFF
    ON: Front passenger side door power window auto switch operated
    OFF: Front passenger side door power window auto switch not operated
    -
    P Door P/W Up SW
    Front passenger side power window manual up switch signal / ON or OFF
    ON: Front passenger side door power window manual up switch operated
    OFF: Front passenger side door power window manual up switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual down switch signal / ON or OFF
    ON: Front passenger side door power window manual down switch operated
    OFF: Front passenger side door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 6
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) (Click here)  

6.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)


    B193518E13
  1. Remove the power window regulator switch assembly (for front passenger side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Auto up or up position
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Auto down or down position
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω
    6 (UP) - 1 (GND)
    Free
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Free
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Free
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER SIDE SWITCH - FRONT PASSENGER SIDE MOTOR)


    B193519E41
  1. Disconnect the power window regulator motor assembly (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H13-6 (UP) - Body ground
    Always
    10 kΩ or higher
    H13-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    H13-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    H12-10 (UP) - Body ground
    Always
    10 kΩ or higher
    H12-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    H12-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) (Click here)  

8.READ VALUE USING INTELLIGENT TESTER (RL-Door Motor)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / RL-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Side)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Auto SW
    Rear LH side power window auto up/down switch signal / ON or OFF
    ON: Rear LH door power window auto switch operated
    OFF: Rear LH door power window auto switch not operated
    -
    RL Door P/W Up SW
    Rear LH side power window manual up switch signal / ON or OFF
    ON: Rear LH door power window manual up switch operated
    OFF: Rear LH door power window manual up switch not operated
    -
    RL Door P/W Down SW
    Rear LH side power window manual down switch signal / ON or OFF
    ON: Rear LH door power window manual down switch operated
    OFF: Rear LH door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 9
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH side) (Click here)  

9.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Side)


    B193518E14
  1. Remove the power window regulator switch assembly (for rear LH side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Auto up or up position
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Auto down or down position
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω
    6 (UP) - 1 (GND)
    Free
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Free
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Free
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH side) (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (REAR LH SWITCH - REAR LH MOTOR)


    B193519E35
  1. Disconnect the power window regulator motor assembly (for rear LH side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K6-6 (UP) - Body ground
    Always
    10 kΩ or higher
    K6-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    K6-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    K7-10 (UP) - Body ground
    Always
    10 kΩ or higher
    K7-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    K7-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH side) (Click here)  

11.READ VALUE USING INTELLIGENT TESTER (RR-Door Motor)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / RR-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Side)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door P/W Auto SW
    Rear RH side power window auto up/down switch signal / ON or OFF
    ON: Rear RH door power window auto switch operated
    OFF: Rear RH door power window auto switch not operated
    -
    RR Door P/W Up SW
    Rear RH side power window manual up switch signal / ON or OFF
    ON: Rear RH door power window manual up switch operated
    OFF: Rear RH door power window manual up switch not operated
    -
    RR Door P/W Down SW
    Rear RH side power window manual down switch signal / ON or OFF
    ON: Rear RH door power window manual down switch operated
    OFF: Rear RH door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 12
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH side) (Click here)  

12.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Side)


    B193518E15
  1. Remove the power window regulator switch assembly (for rear RH side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Auto up or up position
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Auto down or down position
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω
    6 (UP) - 1 (GND)
    Free
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Free
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Free
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH side) (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (REAR RH SWITCH - REAR RH MOTOR)


    B193519E36
  1. Disconnect the power window regulator motor assembly (for rear RH side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J6-6 (UP) - Body ground
    Always
    10 kΩ or higher
    J6-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J6-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    J7-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J7-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J7-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH side) (Click here)