DTC B2326 CAN MS Bus Line Communication Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B2326 | Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus. |
|


| 1.CHECK VEHICLE TYPE |
| Vehicle Type | Proceed to |
| For vehicle w/o TOYOTA Parking assist-sensor system | A |
| For vehicle w/ TOYOTA Parking assist-sensor system | B |
|
| ||||
| A | |
| 2.CHECK CAN MS BUS WIRE |
Turn the ignition switch off.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Result |
| E74-27 (CANH) - E74-28 (CANL) | Ignition switch off | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in a main bus line | |||
| E74-27 (CANH) - E74-17 (E) | Ignition switch off | 200 Ω or higher | Below 200 Ω: CANH ground short |
| E74-28 (CANL) - E74-17 (E) | Ignition switch off | Below 200 Ω: CANL ground short |
Disconnected the cable from the negative (-) battery terminal.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Result |
| E74-27 (CANH) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| E74-28 (CANL) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
| OK | A |
NG
| B |
NG
| C |
|
| ||||
|
| ||||
| A | |
| 3.RECONFIRM DTC OUTPUT |
Clear DTCs.
Turn the ignition switch off.
Turn the ignition switch ON, recheck the DTC.
| Result | Proceed to |
| B2326 output | A |
| Other DTC output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK CAN MS BUS WIRE |
Turn the ignition switch off.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Result |
| O32-1 (CANH) - O32-2 (CANL) | Ignition switch off | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in a main bus line | |||
| O32-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher | Below 200 Ω: CANH ground short |
| O32-2 (CANL) - E10-4 (CG) | Ignition switch off | Below 200 Ω: CANL ground short |
Disconnected the cable from the negative (-) battery terminal.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Result |
| O32-1 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| O32-2 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
| OK | A |
| NG (Open circuit in a main bus line) | B |
| NG (Short circuit between bus lines) | C |
| NG (+B short) | D |
| NG (Ground short) | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 5.CHECK FOR OPEN IN CAN MS BUS WIRE (CAN MS BUS BRANCH WIRE) |
Check for the clearance warning ECU sub bus branch wire and power source circuit (Click here).
|
| ||||
| OK | |
| 6.REPLACE CLEARANCE WARNING ECU |
Replace the clearance warning ECU (Click here).
| NEXT | |
| 7.CHECK DTC OUTPUT |
Clear DTCs.
Check for the DTC.
| Result | Proceed to |
| B2326 not output | A |
| B2326 output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 3 J/C - MAIN BODY ECU) |
![]() |
Disconnect the CAN MS bus main wire connector (O32) from the No. 3 CAN J/C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O32-1 (CANH) - O32-2 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| OK (w/ Entry and start system) | A |
| OK (w/o Entry and start system) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 9.CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
Reconnect the certification ECU main wire connector (O32) to the No. 3 CAN J/C.
![]() |
Disconnect the certification ECU main wire connector (O33) from the No. 3 CAN J/C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O33-1 (CANH) - O33-2 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 10.CHECK OPEN IN CAN BUS MAIN WIRE |
![]() |
Disconnect the certification ECU connector (E74).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-28 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Reconnect the CAN MS bus main wire connector (O32) to the No. 3 CAN J/C.
![]() |
Disconnect the main body ECU connector (E8) from the main body ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E8-16 (CANP) - E8-15 (CANN) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 12.CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C WIRE) |
![]() |
Disconnect the CAN MS bus main wire connector (O32) from the No. 3 CAN J/C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O32-1 (CANH) - O32-2 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| OK (w/ Entry and start system) | A |
| OK (w/o Entry and start system) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 13.CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU MAIN WIRE) |
![]() |
Disconnect the certification ECU main wire connector (O33) from the No. 3 CAN J/C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O33-1 (CANH) - O33-2 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| NG | |
| 14.CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU - CAN NO. 3 J/C) |
Reconnect the certification ECU main wire connector (O33) to the No. 3 CAN J/C.
![]() |
Disconnect the certification ECU connector (E74).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-28 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 15.CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE) |
Reconnect the certification ECU main wire connector (O33) to the No. 3 CAN J/C.
Disconnect the clearance warning ECU connector (O28).
![]() |
Disconnect the main body ECU main wire connector (O31) from the No. 3 CAN J/C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O31-1 (CANH) - O31-2 (CANL) | Ignition switch off | 1 MΩ or higher |
|
| ||||
| OK | |
| 16.CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU) |
Reconnect the main body ECU main wire connector (O31) to the No. 3 CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O28-3 (R1) - O28-5 (R2) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Reconnect the CAN MS bus main wire connector (O32) to the No. 3 CAN J/C.
![]() |
Disconnect the main body ECU connector (E8) from the main body ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E8-16 (CANP) - E8-15 (CANN) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 18.CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE) |
![]() |
Disconnect the CAN MS bus main wire connector (O32) from the No. 3 CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O32-1 (CANH) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| O32-2 (CANL) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| Result | Proceed to |
| OK (w/ Entry and start system) | A |
| OK (w/o Entry and start system) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 19.CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
![]() |
Disconnect the certification ECU main wire connector (O33) from the No. 3 CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O33-1 (CANH) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| O33-2 (CANL) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | |
| 20.CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C) |
Disconnect the clearance warning ECU connector (O28).
![]() |
Disconnect the clearance warning ECU branch wire connector (O31) from the No. 3 CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O31-1 (CANH) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| O31-2 (CANL) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 21.CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
![]() |
Disconnect the certification ECU connector (E74).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O33-1 (CANH) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| O33-2 (CANL) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 22.CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
![]() |
Disconnect the main body ECU connector E8 from the main body ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O32-1 (CANH) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| O32-2 (CANL) - E10-16 (BAT) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 23.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE) |
![]() |
Disconnect the CAN MS bus main wire connector (O32) from the No. 3 CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O32-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| O32-2 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| Result | Proceed to |
| OK (w/ Entry and start system) | A |
| OK (w/o Entry and start system) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 24.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C) |
![]() |
Disconnect the certification ECU main wire connector (O33) from the No. 3 CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O33-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| O33-2 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 25.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C) |
Disconnect the clearance warning ECU connector (O28).
![]() |
Disconnect the clearance warning ECU branch wire connector (O31) from the No. 3 CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O31-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| O31-2 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 26.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO . 3 J/C) |
![]() |
Disconnect the certification ECU connector (E74).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O33-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| O33-2 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 27.CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
![]() |
Disconnect the main body ECU connector E8 from the main body ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| O32-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| O32-2 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 28.CHECK CAN BUS MAIN WIRE (CERTIFICATION ECU) |
Disconnect the E74 certification ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-28 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 29.CHECK CAN BUS MAIN WIRE (MAIN BODY ECU - CERTIFICATION ECU) |
Reconnect the certification ECU connector.
![]() |
Disconnect the E8 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E8-16 (CANP) - E8-15 (CANN) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 30.CHECK CAN BUS MAIN WIRE (CERTIFICATION ECU) |
Disconnect the E74 certification ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-28 (CANL) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-27 (CANH) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E74-28 (CANL) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 31.CHECK CAN BUS MAIN WIRE (MAIN BODY ECU - CERTIFICATION ECU) |
Disconnect the E8 main body ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E74-27 (CANH) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-28 (CANL) - E74-17 (E) | Ignition switch off | 200 Ω or higher |
| E74-27 (CANH) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E74-28 (CANL) - E74-1 (+B) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||