Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows) > Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH

for Preparation Click here


DESCRIPTION

If the manual up/down function can be performed but the auto up/down function cannot, the fail-safe mode may be functioning.
If the power window initialization (Click here) has not been performed, the auto up/down function will not operate.

WIRING DIAGRAM


B203367E31


INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses a multiplex communication system (LIN communication system). Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  2. When the power window regulator motor assembly (for rear LH side) is reinstalled or replaced, the power window control system must be initialized.
  3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
    1. Close the power window by fully pulling up the power window regulator switch assembly (for rear LH side) and holding it at the auto up position.
    2. Open the power window by fully pushing down the power window regulator switch assembly (for rear LH side).
  4. When the ECU determines that the power window regulator motor assembly (for rear LH side) has a malfunction, DTC B2311 is set.

1.READ VALUE USING INTELLIGENT TESTER (RL-Door Motor)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / RL-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Side)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Auto SW
    Rear LH side power window auto switch signal / ON or OFF
    ON: Rear LH power window auto switch operated
    OFF: Rear LH power window auto switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


2.PERFORM INITIALIZATION (for Rear LH Side)
  1. Initialize the power window regulator motor assembly (for rear LH side) (Click here).


NEXT


3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
  1. Check that the rear LH side door power window moves when the auto up/down function of the power window regulator switch assembly (for rear LH side) is operated (Click here).

    OK:
    Rear LH side auto up/down function is normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Side) (Click here)
OK

END (PROBLEM DUE TO INITIALIZATION FAILURE) 

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Side)


    B193518E20
  1. Remove the power window regulator switch assembly (for rear LH side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Side) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (REAR LH SIDE SWITCH - REAR LH SIDE MOTOR)


    B193519E39
  1. Disconnect the power window regulator motor assembly (for rear LH side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K6-8 (AUTO) - K7-4 (AUTO)
    Always
    Below 1 Ω
    K6-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Side) (Click here)