Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

TOYOTA PARKING ASSIST-SENSOR SYSTEM > Clearance Sonar Main Switch Circuit

for Preparation Click here


DESCRIPTION

The clearance sonar main switch assembly is installed at the base of the driver side instrument panel.
When the clearance sonar main switch is turned on, an ON signal is sent to the clearance warning ECU. The Toyota parking assist-sensor system operates according to this signal.

WIRING DIAGRAM


E149972E08


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Clearance Sonar / Data List.

  1. Check the Data List for proper functioning of the following items.

    Clearance Sonar 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main Switch
    Clearance sonar main switch/OFF or ON
    OFF: Clearance sonar main switch off
    ON: Clearance sonar main switch on with indicator illuminated
    -
    Clearance Sonar ECU
    ECU information/Normal or Abnormal
    Normal: ECU normal
    Abnormal: ECU not normal
    -

    Result:
    Result
    Proceed to
    Both of the following conditions are met:
    1. The display changes as shown above when the clearance sonar main switch is operated.
    1. "Normal" is displayed.
    A
    "Normal" is not displayed.
    B
    Both of the following conditions are met:
    1. The display does not change as shown above when the clearance sonar main switch is operated.
    1. "Normal" is displayed.
    C



B
REPLACE CLEARANCE WARNING ECU (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT CLEARANCE SONAR MAIN SWITCH ASSEMBLY
  1. Remove the clearance sonar main switch assembly (Click here).



    B139331E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E71-6 (IG) - E71-3 (ECU)
    Clearance sonar main switch is pushed
    Below 1 Ω
    E71-6 (IG) - E71-3 (ECU)
    Clearance sonar main switch is not pushed
    10 kΩ or higher



NG
REPLACE CLEARANCE SONAR MAIN SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CLEARANCE SONAR MAIN SWITCH - BATTERY)


    E168460E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E71-6 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    E71-6 (IG) - Body ground
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (CLEARANCE SONAR MAIN SWITCH - ECU)


    E168445E02
  1. Disconnect the clearance warning ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O28-12 (CLSW) - E71-3 (ECU)
    Always
    Below 1 Ω
    O28-12 (CLSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CLEARANCE WARNING ECU (Click here)