Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073925 ENGINE G

2AR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or a blockage in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or a blockage remains even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 13750 6.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.

If any defects or problems are found during the inspection above, perform a lash adjuster inspection.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


Hide 7.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.

NOTICE:

When checking the ignition timing, the transmission should be in neutral.



ii.

Start the engine and idle it.


iii.

Turn the intelligent tester main switch on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:

BTDC 5 to 15 deg. at idle


HINT:

Refer to the intelligent tester operator's manual for further details.

If the ignition timing is not as specified, check the valve timing.



v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vii.

Monitor IGN Advance of the Data List.

Standard ignition timing:

BTDC 8 to 12 deg. at idle


HINT:

Refer to the intelligent tester operator's manual for further details.

If the ignition timing is not as specified, check the valve timing.



viii.

Enter the following menus: Connect the TC and TE1 / OFF.


ix.

Turn the ignition switch off.


x.

Disconnect the intelligent tester from the DLC3.



c.

When not using the intelligent tester:

i.

Remove the No. 1 engine cover sub-assembly.


ii.

Pull out the wire harness.


iii.
A210177

Connect the clip of a timing light to the wire harness.

NOTICE:

Use a timing light that detects primary signals.



iv.
A122830C39
1.094,0.604 1.552,1.063 false 1.76,1.656 1.375,2.042 false 0.927,1.063 1.042,1.219 0.115,0.156 10 false 1 0.927,1.469 1.042,1.625 0.115,0.156 10 false 9 1.104,1.469 1.281,1.625 0.177,0.156 10 false 10 1.302,1.469 1.479,1.625 0.177,0.156 10 false 11 1.51,1.469 1.688,1.625 0.177,0.156 10 false 12 1.719,1.469 1.896,1.625 0.177,0.156 10 false 13 1.927,1.469 2.104,1.625 0.177,0.156 10 false 14 2.125,1.469 2.302,1.625 0.177,0.156 10 false 15 2.333,1.469 2.51,1.625 0.177,0.156 10 false 16 1.135,1.063 1.25,1.219 0.115,0.156 10 false 2 1.344,1.063 1.458,1.219 0.115,0.156 10 false 3 1.552,1.063 1.667,1.219 0.115,0.156 10 false 4 1.75,1.063 1.865,1.219 0.115,0.156 10 false 5 1.958,1.063 2.073,1.219 0.115,0.156 10 false 6 2.156,1.063 2.271,1.219 0.115,0.156 10 false 7 2.365,1.063 2.479,1.219 0.115,0.156 10 false 8 1.594,0.156 1.76,0.333 0.167,0.177 10 false *1 0.875,0.479 1.188,0.677 0.313,0.198 10 false CG 1.156,1.958 1.469,2.156 0.313,0.198 10 false TC
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminals before connecting them. Connecting the wrong terminals may result in damage to electrical components.

·

When checking the ignition timing, the transmission should be in neutral.




v.

Using a timing light, check the ignition timing.

Standard ignition timing:

8 to 12° BTDC at idle



vi.

Remove SST from the DLC3.


vii.

Check the ignition timing.

Standard ignition timing:

5 to 15° BTDC at idle


If the ignition timing is not as specified, check the valve timing.


viii.

Check that the ignition timing advances immediately when the engine speed is increased.


ix.

Disconnect the timing light from the engine.


x.

Install the No. 1 engine cover sub-assembly.



Hide 8.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.

NOTICE:
·

Switch off all accessories and the A/C before connecting the intelligent tester.

·

When checking the idle speed, the transmission should be in neutral.




ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Turn the intelligent tester main switch on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9
Standard Idle Speed:
Transaxle Idling Speed
Manual Transaxle 750 to 850 rpm
Automatic Transaxle 610 to 710 rpm


HINT:

Refer to the intelligent tester operator's manual for further details.


If the idle speed is not as specified, check the air intake system.


v.

Disconnect the intelligent tester from the DLC3.



c.

When not using the intelligent tester:

i.
A122830C40
0.823,1.958 0.969,1.667 false 0.927,1.063 1.042,1.219 0.115,0.156 10 false 1 0.927,1.469 1.042,1.625 0.115,0.156 10 false 9 1.104,1.469 1.281,1.625 0.177,0.156 10 false 10 1.302,1.469 1.479,1.625 0.177,0.156 10 false 11 1.51,1.469 1.688,1.625 0.177,0.156 10 false 12 1.719,1.469 1.896,1.625 0.177,0.156 10 false 13 1.927,1.469 2.104,1.625 0.177,0.156 10 false 14 2.125,1.469 2.302,1.625 0.177,0.156 10 false 15 2.333,1.469 2.51,1.625 0.177,0.156 10 false 16 1.135,1.063 1.25,1.219 0.115,0.156 10 false 2 1.344,1.063 1.458,1.219 0.115,0.156 10 false 3 1.552,1.063 1.667,1.219 0.115,0.156 10 false 4 1.75,1.063 1.865,1.219 0.115,0.156 10 false 5 1.958,1.063 2.073,1.219 0.115,0.156 10 false 6 2.156,1.063 2.271,1.219 0.115,0.156 10 false 7 2.365,1.063 2.479,1.219 0.115,0.156 10 false 8 1.594,0.156 1.948,0.396 0.354,0.24 10 false *1 0.688,2 1.083,2.177 0.396,0.177 10 false TAC
*1 DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:
·

Confirm the terminal before connecting them. Connecting the wrong terminals may result in damage to electrical components.

·

Turn all electrical systems and the A/C off.

·

Inspect the idle speed with the cooling fans off.

·

When checking the idle speed, the transaxle should be in neutral.




ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Check the idle speed.

Standard Idle Speed:
Transaxle Idling Speed
Manual Transaxle 750 to 850 rpm
Automatic Transaxle 610 to 710 rpm


If the speed is not as specified, check the air intake system.


iv.

Disconnect the tachometer probe from the DLC3.



Hide 9.INSPECT COMPRESSION

a.

Warm up and stop the engine.




d.

Disconnect the 4 fuel injector connectors.


e.
A195864

Insert a compression gauge into the spark plug hole.


f.

Fully open the throttle.


g.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1450 kPa (14.8 kgf/cm2, 210 psi)


Minimum pressure:

980 kPa (10.0 kgf/cm2, 142 psi)


Difference between each cylinder:

100 kPa (1.0 kgf/cm2, 15 psi)


HINT:

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.



h.

If the cylinder compression is low in one or more cylinders, pour a small amount of engine oil into the cylinder with low compression through its spark plug hole. Then inspect the cylinder compression pressure again.

HINT:
·

If adding oil helps boost the compression, it is likely that the piston rings and/or cylinder bore is worn or damaged.

·

If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.




i.

Connect the 4 fuel injector connectors.




Hide 10.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Keep the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.


d.

Immediately check CO/HC concentration at idle and 2500 rpm.

HINT:
·

When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

·

If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.




ii.

See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

CO HC Symptom Causes
Normal High Rough idle

1. Faulty ignition

·

Incorrect timing

·

Plugs are contaminated or shorted, or gaps are defective


2. Leaky intake and exhaust valves

3. Leaky cylinder


Low High Rough idle
(Fluctuating HC reading)

1. Vacuum leaks

·

PCV hose

·

Intake manifold

·

Throttle body

·

Brake booster line


2. Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)

1. Restricted air filter

2. Faulty SFI system

·

Faulty pressure

·

Defective ECT sensor

·

Faulty ECM

·

Faulty injector

·

Faulty throttle position sensor

·

Faulty MAF sensor