Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL INJECTOR
RM19V0EQ _51 Engine / Hybrid System _014575 2AR-FE FUEL _0073936 FUEL INJECTOR A

2AR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A196010C02
2.521,1.781 2.698,1.781 2.698,1.781 3.135,1.365 false 2.344,1.698 2.51,1.896 0.167,0.198 10 *1
*1 O-ring


Apply a light coat of gasoline or spindle oil to new O-rings, and then install one onto each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil where the fuel delivery pipe contacts each O-ring.


c.
A297393

While turning the fuel injector assembly left and right, install it to the fuel delivery pipe.

NOTICE:
·

Do not damage the fuel injector assembly and O-ring.

·

Do not twist the O-ring.

·

After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.



HINT:

Use the same procedure to install the other fuel injector assemblies.



Hide 23814B 2.INSTALL FUEL DELIVERY PIPE

a.

Install 4 new injector vibration insulators to the cylinder head.

A261674C02
1.823,0.771 1.604,0.771 false 5.323,0.813 5.104,0.813 false 0.75,0.073 0.958,0.333 0.208,0.26 10 false *A 4.302,0.073 4.51,0.333 0.208,0.26 10 false *B 1.729,0.365 1.938,0.625 0.208,0.26 10 false *a 1.729,1.063 1.938,1.323 0.208,0.26 10 false *b 2.469,0.688 2.677,0.948 0.208,0.26 10 false *c 1.438,0.698 1.646,0.958 0.208,0.26 10 false *1 5.219,0.354 5.427,0.615 0.208,0.26 10 false *a 5.219,1.125 5.427,1.385 0.208,0.26 10 false *b 5.979,0.74 6.188,1 0.208,0.26 10 false *d 4.948,0.729 5.156,0.99 0.208,0.26 10 false *1 2.052,1.76 2.24,1.927 0.188,0.167 10 true *1 2.458,1.479 2.646,1.646 0.188,0.167 10 true *1 5.542,1.76 5.729,1.927 0.188,0.167 10 true *1 5.906,1.49 6.094,1.656 0.188,0.167 10 true *1 1.938,2.542 2.125,2.708 0.188,0.167 10 true *2 2.281,2.375 2.469,2.542 0.188,0.167 10 true *2 2.583,2.208 2.771,2.375 0.188,0.167 10 true *2 2.865,2.083 3.052,2.25 0.188,0.167 10 true *2 5.448,2.542 5.635,2.708 0.188,0.167 10 true *2 5.792,2.365 5.979,2.531 0.188,0.167 10 true *2 6.094,2.219 6.281,2.385 0.188,0.167 10 true *2 6.365,2.083 6.552,2.25 0.188,0.167 10 true *2
*A Fuel Delivery Pipe Type A *B Fuel Delivery Pipe Type B
*1 Fuel Delivery Spacer *2 Injector Vibration Insulator
*a Fuel Delivery Pipe Side *b Cylinder Head Side
*c 20.7 mm (0.815 in.) *d 26.0 mm (1.03 in.)



b.

Install the 2 fuel delivery spacers to the cylinder head.

HINT:

Install the fuel delivery spacer so that the longer protrusion is on the cylinder head side.



c.

Install the fuel delivery pipe with the 4 fuel injector assemblies with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

Do not drop the fuel injector assemblies when installing the fuel delivery pipe.

·

Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe.




Hide 3.CONNECT WIRE HARNESS

a.
A252630

Engage the clamp to connect the wire harness.


b.

Install the 2 wire harness brackets to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 4 fuel injector assembly connectors, throttle body with motor assembly connector and sensor wire connector.


Hide 17650 4.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 23901 5.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A297392C08
2.167,3.469 2.302,2.802 2.302,2.802 2.396,2.802 false 1.813,3.271 1.594,2.771 1.594,2.771 1.49,2.771 false 0.854,4.146 0.854,3.813 false 1.396,3.802 1.5,4.229 1.5,4.229 1.563,3.802 false 2.01,3.865 2.344,4.156 2.344,4.156 2,3.406 false 2.74,3.479 2.542,4.219 2.542,4.219 2.792,3.823 false 2.448,2.719 2.76,2.875 0.313,0.156 10 false *a 1.313,2.698 1.625,2.854 0.313,0.156 10 false *b 0.781,4.177 1.146,4.448 0.365,0.271 10 false *c 1.438,4.26 1.75,4.417 0.313,0.156 10 false *d 2.365,4.177 2.677,4.333 0.313,0.156 10 false *e
*a Fuel Pipe
*b Fuel Tube Connector
*c Nylon Tube
*d O-ring
*e Retainer


Engage the clamp to connect the fuel tube sub-assembly to the fuel hose clamp.


b.

Connect the fuel tube sub-assembly to the fuel pipe.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.

Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



c.
A241745

Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp.


Hide 6.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 9.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY