Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2011.10–2013.07
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073931 ENGINE ASSEMBLY A

2AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the manual transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust from the moving section could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.REMOVE ENGINE STAND

a.

Using a chain block and engine sling device, secure the engine assembly.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent the engine assembly or engine hanger from deforming or becoming damaged.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.




b.

Remove the engine stand from the engine.


Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)

Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 31250 4.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 5.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 6.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 7.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 31407B 8.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

Hide 9.INSPECT CLUTCH PIPE LINE (for Manual Transaxle)

Hide 31407B 10.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

Hide 11.REMOVE CLUTCH LINE (for Manual Transaxle)

Hide 30300 12.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 30500 13.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)

Hide 12315A 14.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH with the 3 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 12321A 15.INSTALL REAR ENGINE MOUNTING BRACKET (for Manual Transaxle)

a.

Install the rear engine mounting bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12322 16.INSTALL NO. 2 REAR ENGINE MOUNTING BRACKET (for Manual Transaxle)

a.

Install the No. 2 rear engine mounting bracket with the 2 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 43457 17.INSTALL DRIVE SHAFT BEARING BRACKET (for Automatic Transaxle)

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12361A 18.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Temporarily install the front engine mounting insulator with the bolt.


Hide 12372A 19.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH (for Manual Transaxle)

a.

Temporarily install the engine mounting insulator LH with the 3 bolts.


Hide 12372A 20.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH (for Automatic Transaxle)

a.

Temporarily install the engine mounting insulator LH with the nut.


Hide 12362A 21.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH

a.

Temporarily install the engine mounting insulator RH with the nut.


Hide 12364A 22.TEMPORARILY INSTALL ENGINE LATERAL CONTROL ROD (for Manual Transaxle)

a.

Temporarily install the engine lateral control rod with the through bolt and nut.


Hide 51100G 23.INSTALL FRONT FRAME ASSEMBLY

a.

Install the front frame assembly with the 9 nuts.

A172973C08
0.469,0.25 0.656,0.438 0.188,0.188 10 false *a 2.375,0.229 2.573,0.417 0.198,0.188 10 false *b 4.865,0.219 5.073,0.406 0.208,0.188 10 false *c 0.177,1.938 0.313,2.104 0.135,0.167 10 false A 0.688,1.573 0.823,1.74 0.135,0.167 10 true A 1.469,1.823 1.604,1.99 0.135,0.167 10 true A 3.021,0.958 3.156,1.125 0.135,0.167 10 false B 3.448,1.385 3.583,1.552 0.135,0.167 10 false B 3.604,0.802 3.74,0.969 0.135,0.167 10 true B 5.406,1.052 5.542,1.219 0.135,0.167 10 true B 6.01,1.094 6.146,1.26 0.135,0.167 10 false B 6.219,1.979 6.354,2.146 0.135,0.167 10 false B
*a Front Side *b RH Side
*c LH Side - -


Torque:
A : 52 N*m (530 kgf*cm, 38 ft.*lbf)
B : 87 N*m (887 kgf*cm, 64 ft.*lbf)


b.

Install the 4 hole plugs.


c.

for Manual Transaxle:

i.

Tighten the 4 bolts and nut.

A265025C01
0.302,0.469 1.25,0.708 0.948,0.24 10 false *a 2.844,0.469 3.667,0.688 0.823,0.219 10 false *b 5.073,0.469 5.896,0.688 0.823,0.219 10 false *c 1.083,1.656 1.198,1.813 0.115,0.156 10 true A 3.719,0.656 3.833,0.813 0.115,0.156 10 false B 5.938,0.823 6.052,0.979 0.115,0.156 10 true C 4.24,1.146 4.354,1.302 0.115,0.156 10 true B 2.771,2.188 2.885,2.344 0.115,0.156 10 true B
*a Front Side *b LH Side
*c RH Side - -


Torque:
A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
B : 64 N*m (653 kgf*cm, 47 ft.*lbf)
C : 95 N*m (969 kgf*cm, 70 ft.*lbf)


ii.

Install the engine lateral control rod with the 2 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


iii.

Install the 2 hole plugs.


iv.

Tighten the through bolt and nut.

Torque:
89 N*m (908 kgf*cm, 65 ft.*lbf)



d.

for Automatic Transaxle:

i.

Tighten the bolt and 2 nuts.

A265024C02
0.344,0.198 1.292,0.438 0.948,0.24 10 false *a 2.885,0.198 3.708,0.417 0.823,0.219 10 false *b 1.094,1.344 1.229,1.51 0.135,0.167 10 true A 3.792,0.615 3.927,0.781 0.135,0.167 10 true B 5.927,0.563 6.063,0.729 0.135,0.167 10 true C 5.167,0.198 5.99,0.417 0.823,0.219 10 false *c
*a Front Side *b LH Side
*c RH Side - -


Torque:
A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
B : 95 N*m (969 kgf*cm, 70 ft.*lbf)
C : 95 N*m (969 kgf*cm, 70 ft.*lbf)



Hide 43420G 24.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43420 25.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 26.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

Hide 27020 27.INSTALL GENERATOR ASSEMBLY

Hide 88310 28.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

Hide 82121 30.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine with transaxle.


Hide 31.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

·

Do not position a height adjustment attachment or plate lift attachment onto the front frame assembly.

·

To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.

·

Make sure to support the engine assembly with transaxle securely to prevent it from falling.





c.

Install the engine assembly to the vehicle.

NOTICE:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


HINT:
·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.




d.
A255454N06
2.198,3.031 2.344,3.198 0.146,0.167 10 false C 1.125,3.021 1.271,3.188 0.146,0.167 10 false C 0.677,1.344 0.823,1.51 0.146,0.167 10 true A 2.635,1.333 2.781,1.5 0.146,0.167 10 true A 1.01,0.083 1.156,0.25 0.146,0.167 10 false B 2.615,0.104 2.76,0.271 0.146,0.167 10 false B 3.135,0.323 3.281,0.49 0.146,0.167 10 false B 0.167,0.313 0.313,0.479 0.146,0.167 10 false B 3.156,2.417 3.302,2.583 0.146,0.167 10 false D 2.708,3.188 2.854,3.354 0.146,0.167 10 true D 0.167,2.417 0.313,2.583 0.146,0.167 10 false D 0.542,3.188 0.688,3.354 0.146,0.167 10 false D

Install the frame side rail plate RH and LH with the 4 bolts and 2 nuts.

Torque:
A : 85 N*m (867 kgf*cm, 62 ft.*lbf)
B : 32 N*m (326 kgf*cm, 24 ft.*lbf)


e.

Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.

Torque:
C : 85 N*m (867 kgf*cm, 62 ft.*lbf)
D : 32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 32101A 32.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for Automatic Transaxle)

a.
A192239C51
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to the first 2 or 3 threads of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A196626

Turn the crankshaft to gain access to the installation locations of the 6 torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the 5 silver colored bolts.



Hide 11361J 33.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover.


Hide 45220 34.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 43502C 35.INSTALL FRONT AXLE ASSEMBLY LH

Hide 43501C 36.INSTALL FRONT AXLE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 37.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 38.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 39.INSTALL TIE ROD ASSEMBLY LH

Hide 45460 40.INSTALL TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89543 41.INSTALL FRONT SPEED SENSOR LH

Hide 89542 42.INSTALL FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 43.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 44.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 45.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 46.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 17410 47.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 31418 48.CONNECT CLUTCH HOSE (for Manual Transaxle)

a.

Using a union nut wrench (10 mm), install the flexible hose tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 23901 49.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
B012944

Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.

NOTICE:
·

Check for damage or contamination on the connected part of the pipe.

·

Check if the pipe and the connector are securely connected by trying to pull them apart.




b.
A210152

Install the No. 1 fuel pipe clamp.


Hide 88711 50.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 51.INSTALL SUCTION HOSE SUB-ASSEMBLY

Hide 44774 52.CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

a.

Connect the union to connector tube hose.


Hide 44773F 53.CONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.

Connect the union to check valve hose.


Hide 12309 54.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

a.
A255452

Temporarily install the engine moving control rod sub-assembly with the 4 bolts.


b.

Fully tighten the engine moving control rod sub-assembly with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 82284 55.INSTALL EARTH WIRE

a.

Install the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12327A 56.INSTALL NO. 2 ENGINE MOUNTING STAY RH

a.

Install the No. 2 engine mounting stay RH with the 2 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 33820B 57.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.
C248128

Install the transmission control cable assembly to the control cable bracket with 2 new clips.


b.

Install the 2 new clips.


c.
C248131C02
2.01,0.125 1.917,0.125 1.917,0.125 1.656,0.792 true 0.813,1.25 0.99,1.25 0.99,1.25 1.5,0.938 true 2.031,0.042 2.26,0.229 0.229,0.188 10 false *1 0.635,1.167 0.865,1.365 0.229,0.198 10 false *2
*1 Outer Select Lever
*2 Hole


Align the hole of the outer select lever with the hole in the front transaxle case.


d.
C248132

Insert a bolt into the aligned holes to secure the outer select lever in place.

NOTICE:

Do not push in the bolt forcefully or damage the front transaxle case.


HINT:
·

Use a bolt with a diameter of 6 mm (0.236 in.) and a length of at least 16 mm (0.630 in.).

·

Depending on the bolt diameter, it may be difficult to insert the bolt. In that case, use a bolt with a diameter smaller than 6 mm (0.236 in.).




Hide 33820B 58.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

a.

Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.


b.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.



c.

Connect the wire harness clamp.


Hide 17771A 59.INSTALL NO. 1 AIR CLEANER BRACKET

a.

Install the No. 1 air cleaner bracket to the battery carrier with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 2 wire clamps.


Hide 82121 60.CONNECT ENGINE WIRE

a.

for automatic transaxle:

i.
A255463

Connect the 2 wire clamps.


ii.

Connect the connector to the ECM with the lock lever.



b.

for manual transaxle:

i.
A264864

Connect the 2 wire clamps and install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Connect the connector to the ECM with the lock lever.



c.

Connect the engine wire to the engine room relay block.


d.

Connect the 4 connectors.


e.
A255437

Connect the engine wire to the engine room relay block.


f.

Connect the wire clamp and install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

Install the No. 1 relay block cover.


Hide 28100 61.INSTALL STARTER ASSEMBLY

Hide 87245 62.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose.


Hide 87246 63.CONNECT OUTLET HEATER WATER HOSE (for LHD)

a.

Connect the outlet heater water hose.


Hide 87246 64.CONNECT OUTLET HEATER WATER HOSE (for RHD)

a.

Connect the 3 heater outlet water hoses.


Hide 32941 65.CONNECT INLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle LHD)

a.

Connect the inlet No. 1 oil cooler hose to the automatic transaxle assembly.


Hide 32942 66.CONNECT OUTLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle LHD)

a.

Connect the outlet No. 1 oil cooler hose to the automatic transaxle assembly.


Hide 16571C 67.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose.


b.

Connect the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.


Hide 16572D 68.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose.


Hide 69.INSTALL BATTERY

a.

Install the battery and battery tray.


b.

Install the battery clamp with the bolt and nut.

Torque:
Bolt : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Nut : 3.5 N*m (36 kgf*cm, 31 in.*lbf)


c.

Connect the positive (+) battery terminal

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


Hide 70.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.
A305724C01
2.229,0.958 2.583,1.115 true 2.667,0.833 2.896,0.833 true 2.094,0.844 2.406,1 0.313,0.156 10 false *1 2.906,0.74 3.104,0.906 0.198,0.167 10 false *2
*1 Hole
*2 Projection


Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.


b.

Tighten the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the wire harness clamp.


Hide 17801 71.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 72.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 73.INSTALL INLET AIR CLEANER ASSEMBLY

a.

Install the inlet air cleaner assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 74.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 75.ADD ENGINE OIL

Hide 77.ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)

Hide 78.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 79.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 81. WARM UP ENGINE

Hide 83.INSPECT FOR OIL LEAK

Hide 85.INSPECT FOR EXHAUST GAS LEAK

Hide 12601B 90.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Engage the 3 pins and install the No.1 engine cover sub-assembly.


Hide 53737B 92.INSTALL FRONT FENDER APRON SEAL LH

Hide 53736 93.INSTALL FRONT FENDER APRON SEAL RH

Hide 51442C 94.INSTALL ENGINE UNDER COVER LH

Hide 53852K 95.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 51441C 96.INSTALL ENGINE UNDER COVER RH

Hide 53851Z 97.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 98.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 99.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT