Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL INJECTOR
RM19V0EQ _51 Engine / Hybrid System _014575 2AR-FE FUEL _0073936 FUEL INJECTOR A

2AR-FE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A296983

Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector.


b.
A296959C06
2.385,2.875 2.313,2.875 2.313,2.875 2.198,3.469 false 1.792,3.271 1.719,2.865 1.719,2.865 1.635,2.865 false 0.854,4.167 0.854,3.823 false 1.396,3.813 1.479,4.229 1.479,4.229 1.563,3.813 false 2.74,3.49 2.365,4.229 2.365,4.229 2.792,3.823 false 2,3.854 2.271,4.219 2.271,4.219 1.979,3.438 false 2.427,2.802 2.74,2.958 0.313,0.156 10 false *a 1.458,2.792 1.781,3.063 0.323,0.271 10 false *b 0.771,4.188 1.083,4.344 0.313,0.156 10 false *c 1.417,4.26 1.729,4.417 0.313,0.156 10 false *d 2.24,4.26 2.552,4.417 0.313,0.156 10 false *e
*a Fuel Pipe
*b Fuel Tube Connector
*c Nylon Tube
*d O-ring
*e Retainer
V100135

Pinch
V100136

Pull


Disconnect the fuel tube sub-assembly from the fuel pipe.

i.

Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Disengage the clamp to disconnect the fuel tube sub-assembly from the fuel hose clamp.


Hide 17650 7.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 8.DISCONNECT WIRE HARNESS

A252630

a.

Disconnect the 4 fuel injector assembly connectors, throttle body with motor assembly connector and sensor wire connector.


b.

Remove the 2 bolts and separate the 2 wire harness brackets from the intake manifold.


c.

Disengage the clamp to disconnect the wire harness.


Hide 23814B 9.REMOVE FUEL DELIVERY PIPE

a.

Remove the 2 bolts and fuel delivery pipe with the 4 fuel injector assemblies.

A261673C02
0.504,0.026 0.697,0.219 0.192,0.192 10 *A 4.046,0.026 4.238,0.219 0.192,0.192 10 *B
*A Fuel Delivery Pipe Type A *B Fuel Delivery Pipe Type B


NOTICE:

Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe.



b.
A211217C03
1.417,1.031 1.729,1.188 0.313,0.156 10 true *1 1.948,1.781 2.26,1.938 0.313,0.156 10 true *2 2.24,0.646 2.552,0.802 0.313,0.156 10 true *1 2.344,1.594 2.656,1.75 0.313,0.156 10 true *2 2.708,1.396 3.021,1.552 0.313,0.156 10 true *2 3.073,1.188 3.385,1.344 0.313,0.156 10 true *2
*1 Fuel Delivery Spacer
*2 Injector Vibration Insulator


Remove the 2 fuel delivery spacers from the cylinder head.


c.

Remove the 4 injector vibration insulators from the cylinder head.


Hide 23250 10.REMOVE FUEL INJECTOR ASSEMBLY

a.
A296984

Pull the 4 fuel injector assemblies out of the fuel delivery pipe.


b.

Remove the O-ring from each fuel injector assembly.


c.

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.