Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL PRESSURE PULSATION DAMPER
RM19V0EQ _51 Engine / Hybrid System _014575 2AR-FE FUEL _0073938 FUEL PRESSURE PULSATION DAMPER A

2AR-FE FUEL  FUEL PRESSURE PULSATION DAMPER  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 23901 6.REMOVE FUEL TUBE SUB-ASSEMBLY

A204252C04
2.948,2.583 2.938,4.073 false 1.417,1.333 0.969,0.385 0.969,0.385 0.823,0.385 false 0.646,3.948 0.646,4.156 false 0.802,4.26 1.625,4.26 false 1.771,3.75 2.073,3.75 false 0.646,0.313 0.823,0.51 0.177,0.198 10 false *1 0.51,4.167 0.813,4.417 0.302,0.25 10 false SST 2.479,0.521 2.719,0.792 0.24,0.271 10 false *2 2.875,4.135 3.083,4.344 0.208,0.208 10 false *3 0.927,2.271 1.188,2.552 0.26,0.281 10 true *a 2.125,3.677 2.333,3.885 0.208,0.208 10 false *4
*1 No. 2 Fuel Pipe Clamp
*2 Retainer
*3 Fuel Hose Clamp
*4 Fuel Tube Connector
*a Turn


NOTICE:

Do not forcibly bend, kink or twist the fuel tube.


a.

Remove the fuel tube from the fuel hose clamp.


b.

Remove the No. 2 fuel pipe clamp.


c.

Wipe off any dirt on the fuel tube connector.


d.

Hold the fuel tube connector, and then install SST.

SST
09268-21011  


e.

Turn SST to align the retainer inside the fuel tube connector with the chamfered part of SST.


f.

Insert SST into the fuel tube connector and hold it. Then push the fuel tube connector toward SST.


g.

Mount the retainer of the fuel tube connector onto the chamfered part of SST.


h.
A076220C07
2.177,0.76 2.25,0.406 false 2.26,1.573 2.26,1.875 false 0.594,1.375 0.594,1.708 false 1.375,0.875 1.104,0.438 1.104,0.438 1.573,0.875 false 2.917,1.333 2.917,1.542 false 2.25,0.406 2.427,0.406 false 0.969,0.281 1.146,0.479 0.177,0.198 10 *1 2.479,0.344 2.677,0.542 0.198,0.198 10 *2 2.833,1.583 3.01,1.781 0.177,0.198 10 *5 0.531,1.75 0.708,1.948 0.177,0.198 10 *3 2.188,1.896 2.365,2.094 0.177,0.198 10 *4
*1 O-ring
*2 Retainer
*3 Fuel Tube
*4 Fuel Tube Connector
*5 Fuel Pipe


Slide SST and the fuel tube connector together toward the fuel tube until they make a "click" sound, and then disconnect the fuel tube.

NOTICE:
·

Check for foreign matter in the fuel tube around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-rings to seal the fuel tube connector and fuel pipe.

·

Do not use any tools to separate the fuel tube connector and fuel pipe.

·

Do not forcefully bend, kink or twist the fuel tube.

·

Keep the fuel tube connector and fuel pipe free from foreign matter.

·

If the fuel tube connector and fuel pipe are stuck together, pinch the fuel tube connector and turn it carefully to disconnect it.

·

Put the fuel tube connector and fuel pipe in plastic bags to prevent damage and contamination.




Hide 23270 7.REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY

a.
A196014

Remove the 2 bolts and fuel pressure pulsation damper.


b.

Remove the O-ring from the fuel pressure pulsation damper.