Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL PUMP
RM19V0EQ _51 Engine / Hybrid System _014575 2AR-FE FUEL _0073939 FUEL PUMP A

2AR-FE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A136023C02
1.5,0.49 1.083,0.521 false 0.854,0.438 1.031,0.625 0.177,0.188 10 *1
*1 Fuel Suction Tube Set Gasket


Install a new fuel suction tube set gasket to the fuel suction tube.


b.

Install the fuel suction tube with pump and gauge assembly to the fuel tank.

NOTICE:
·

Do not damage the suction filter.

·

Be careful that the arm of the sender gauge does not bend.




Hide 77168A 2.INSTALL FUEL TANK VENT TUBE SET PLATE

a.
A129480C01
2.073,1.25 2.073,1.833 true 2.01,1.844 2.188,2.021 0.177,0.177 10 *a
*a Mark


Align the mark of the set plate with the fuel suction tube.


b.

Install the set plate with the 8 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 77209B 3.CONNECT FUEL PUMP TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate, then install the tube joint clip.

A296960C01
4.521,0.25 5.781,1.583 1.26,1.333 5.833,0.25 7.094,1.583 1.26,1.333 1.646,0.656 1.198,0.156 1.198,0.156 1.104,0.156 false 3.958,0.396 4.094,0.146 4.094,0.146 4.188,0.146 false 3.188,0.75 3.5,0.75 false 3.25,1.24 3.25,0.875 3.25,0.875 3.698,0.875 false 3.25,0.99 3.708,0.99 false 6.615,0.76 6.458,0.479 6.458,0.479 6.365,0.479 false 6.052,0.802 6.365,0.802 false 4.906,0.688 5.219,0.688 false 4.885,1.188 4.979,1.188 4.979,1.188 5.458,0.813 false 0.958,0.083 1.271,0.24 0.313,0.156 10 *1 4.24,0.094 4.552,0.25 0.313,0.156 10 *2 3.177,1.302 3.49,1.458 0.313,0.156 10 *3 6.219,0.417 6.531,0.573 0.313,0.156 10 *4 4.573,0.302 4.885,0.458 0.313,0.156 10 *a 5.875,0.313 6.188,0.469 0.313,0.156 10 *b 3.021,0.667 3.333,0.823 0.313,0.156 10 *1 5.875,0.74 6.188,0.896 0.313,0.156 10 *1 4.74,0.615 5.052,0.771 0.313,0.156 10 *1 4.719,1.135 5.031,1.292 0.313,0.156 10 *4
*1 Tube Joint Clip *2 Fuel Tube Joint
*3 O-ring *4 Collar
*a Correct *b Incorrect


NOTICE:
·

Check that there are no scratches or foreign matter around the connected part of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tube joint cannot be pulled out.




b.

Connect the fuel pump connector.


Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.
A254976C02
2.333,1.135 2.49,1.333 0.156,0.198 10 .
V100144

Butyl Tape


Install the rear floor service hole cover with new butyl tape.


Hide 72693 7.INSTALL REAR SEAT CUSHION LOCK HOOK (for Fixed Seat Type)

Hide 72693 8.INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

Hide 9.INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

Hide 10.INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)