Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › INTAKE MANIFOLD › 2011.10–2016.05
RM19V0EQ _51 Engine / Hybrid System _014577 2AR-FE INTAKE / EXHAUST _0073948 INTAKE MANIFOLD A

2AR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.
A196050

Install the wire harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A292928C02
0.854,1.719 0.99,1.719 0.99,1.719 1.208,1.438 true 0.677,1.625 0.99,1.781 0.313,0.156 10 *a
*a Black


Connect the 2 vacuum hoses and check that the No. 1 check valve is installed as shown in the illustration.


c.

Install a new intake manifold gasket to the intake manifold.


d.
A254723E01
1.823,0.25 2.031,0.479 0.208,0.229 10 false 1 0.542,1.917 0.802,2.167 0.26,0.25 10 false 6 3.208,1.177 3.375,1.365 0.167,0.188 10 false 4 2.542,0.021 2.667,0.167 0.125,0.146 10 false 3 1.031,0.031 1.156,0.177 0.125,0.146 10 false 2 0.448,0.51 0.688,0.75 0.24,0.24 10 false 5

Install the intake manifold by tightening the 6 bolts in the sequence shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


e.
A263239

Connect the 2 wire harness clamps.


f.

Install the wire harness clamp with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
A254751

Install the wire harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


h.

Connect the 3 wire harness clamps and connector.


i.

Connect the fuel vapor feed hose.


j.
A205609

Install the 2 wire harness clamp brackets with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23814B 2.INSTALL FUEL DELIVERY PIPE

Hide 23901 3.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 44774 4.CONNECT UNION TO VACUUM TUBE HOSE (for LHD)

a.

Connect the union to vacuum tube hose to the intake manifold.


Hide 44773F 5.CONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.

Connect the union to check valve hose to the intake manifold.


Hide 12262 6.CONNECT NO. 2 VENTILATION HOSE

a.

Connect the No. 2 ventilation hose to the intake manifold.


Hide 17650 7.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

a.

Install the vacuum switching valve assembly with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.

Connect the 2 vacuum hoses and connector.


c.

Connect the union to connector tube hose and wire harness clamp.


Hide 22030 8.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 55702A 9.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55702A 10.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 11.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 12.CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION