48069
1.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side)
Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.
Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.
While keeping the nut from rotating, tighten the bolt.
Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly with the bolt and 2 nuts.
12372A
2.INSTALL ENGINE MOUNTING INSULATOR LH (for LH Side)
| *a | Pin |
Set the engine mounting insulator LH on the front frame assembly.
Slowly lower the engine assembly with transaxle using a jack and a wooden block.
Match the position of the pin (stopper).
Do not position the wooden block on the oil pan.
Do not damage the components surrounding the engine assembly with transaxle.
Ensure that the jack and wooden block are stable.
| *a | Fulcrum Length |
Using SST, install the nut to the engine mounting insulator LH.
Use a torque wrench with a fulcrum length of 380 mm (1.25 ft.).
This torque value is effective when SST is parallel to the torque wrench.
Install the engine mounting insulator LH with the 3 nuts.
Install the 2 hole plugs.
48068
3.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side)
Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly RH.
Install the front lower No. 1 suspension arm sub-assembly RH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.
While keeping the nut from rotating, tighten the bolt.
Install the front lower No. 1 suspension arm sub-assembly RH to the front lower ball joint assembly with the bolt and 2 nuts.
12362A
4.INSTALL ENGINE MOUNTING INSULATOR RH (for RH Side)
| *a | Cutout |
Set the engine mounting insulator RH on the front frame assembly.
Slowly lower the engine assembly with transaxle using a jack and a wooden block.
Match the position of the cutout (stopper).
Do not position the wooden block on the oil pan.
Do not damage the components surrounding the engine assembly with transaxle.
Ensure that the jack and wooden block are stable.
| *a | Fulcrum Length |
Using SST, install the nut to the engine mounting insulator RH.
Use a torque wrench with a fulcrum length of 380 mm (1.25 ft.).
This torque value is effective when SST is parallel to the torque wrench.
Install the engine mounting insulator RH with the 3 nuts.
Install the 2 hole plugs.
12309
5.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY (for RH Side)
Temporarily install the engine moving control rod sub-assembly with the 4 bolts.
Fully tighten the engine moving control rod sub-assembly with the 4 bolts.
12327A
6.INSTALL NO. 2 ENGINE MOUNTING STAY RH (for RH Side)
82284
7.INSTALL EARTH WIRE (for RH Side)
12361A
8.INSTALL FRONT ENGINE MOUNTING INSULATOR
Install the front engine mounting insulator to the front frame assembly with the 3 nuts.
53737B
9.INSTALL FRONT FENDER APRON SEAL LH (for LH Side)
53736
10.INSTALL FRONT FENDER APRON SEAL RH (for RH Side)
51442C
11.INSTALL ENGINE UNDER COVER LH
51441C
12.INSTALL ENGINE UNDER COVER RH
53852K
13.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)
53851Z
14.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)
15.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
16.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
55702A
18.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55702A
19.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
20.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD)
21.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)
22.INSTALL FRONT WHEELS
23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
24.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT